DOOR AS 2941021 - Caterpillar

2941021 DOOR AS Caterpillar parts 14M, 16M

Price: query

Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2941021
294-1021
2941021

Weight: 44 pounds 19 kg.

Buy DOOR AS 2941021 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER,

Compatible equipment models: 2941021:

MOTOR GRADER 14M 16M Caterpillar

Number on catalog scheme: 18

Caterpillar 2941021 Parts scheme DOOR AS

For full view, you need register

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

16M Motor Grader B9H00001-UP (MACHINE) POWERED BY C13 Engine

294-1023: DOOR GP-CAB » (LH) SEBP41081080
294-1023: DOOR GP-CAB » (LH) SEBP41081081
384-2602: DOOR GP-CAB » (LH) SEBP41081091

14M Motor Grader B9J00001-UP (MACHINE) POWERED BY C11 Engine

294-1023: DOOR GP-CAB » (LH) SEBP42431093
294-1023: DOOR GP-CAB » (LH) SEBP42431094

14M Motor Grader R9J00001-UP (MACHINE) POWERED BY C11 Engine

294-1023: DOOR GP-CAB » (LH) SEBP61221020

16M Motor Grader R9H00001-UP (MACHINE) POWERED BY C13 Engine

294-1023: DOOR GP-CAB » (LH) SEBP61231007
384-2602: DOOR GP-CAB » (LH) SEBP61231016

Information:

This procedure can cause new diagnostic codes to be recorded. Ignore these newly created diagnostic codes. Complete this procedure and then clear the diagnostic codes that were created during this procedure.This diagnostic code is recorded when the ECM reads the voltage of the 5 DCV sensor supply circuit and the ECM determines:
The voltage is too low.
The current is above normal.
CHECK FOR THE CORRECT VOLTAGE AT THE INTERFACE MODULE
Check the voltage at the connector of the interface module from contact 27 (sensor supply) to contact 2 (ground). Use the 7X-1710 Cable probes to measure the voltage. Do NOT disconnect the machine harness from the VIMS main module.Expected Results: Voltage is 5.0 0.5 DCV. Results:
OK - Voltage is 5.0 0.5 DCV. The sensor supply voltage is correct. Check the message center in order to verify that the same diagnostic code is present. If the diagnostic code is still present the interface module has failed. Replace the module. Refer to the Testing and Adjusting, "Module - Replace" section. STOP.
NOT OK - Voltage is less than 5.0 0.5 DCV. The sensor supply voltage is NOT correct. Proceed to 2.
CHECK FOR SHORT TO GROUND
Turn the key start switch and the disconnect switch to the OFFposition.
Disconnect the machine harness from the VIMS interface module.
At the harness connector of VIMS interface module, measure the resistance between frame ground and the contact 27 of the sensor supply circuit. Expected Results: Resistance is greater than 5000 ohms.Results:
OK - Resistance is greater than 5000 ohms. The harness circuit resistance is correct. The VIMS interface module has failed. Replace the VIMS interface module. Refer to the Testing and Adjusting, "Module - Replace" section. STOP.
NOT OK - Resistance is less than 5000 ohms. The machine harness or a sensor has failed. Proceed to 3.
DISCONNECT THE SENSORS.
One at a time disconnect any sensor that uses the +5 DCV interface module sensor supply from the machine harness, that is associated with the diagnostic code.
After disconnecting the sensor, check the resistance from frame ground to contact 27 (sensor supply) of the machine harness connector for the VIMS interface module.Expected Results: Resistance is greater than 5000 ohms.Results:
OK - Resistance is greater than 5000 ohms. The harness circuit resistance is correct. The sensor that was just disconnected has failed. Replace the sensor. STOP.
NOT OK - Resistance is less than 5000 ohms. If the resistance is less than 5000 ohms after all the sensors have been disconnected from the machine harness. The machine harness is shorted to ground. Repair the machine harness or replace the machine harness. STOP.