2D7341 DOOR ASSEM. (RIGHT HAND) Caterpillar parts
12E, 140
Rating:
Alternative (cross code) number:
CA2D7341
2D-7341
2D7341
CA2D7341
2D-7341
2D7341
Weight: 56 pounds 25 kg.
MOTOR GRADER,
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Nickel Anti-Seize Lubricant -
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Illustration 1 g03392235
Remove temperature sensor (3). Disconnect tube assembly (4). Loosen clamp (1) and disconnect strap (2).
Illustration 2 g03385036
Disconnect band clamp (6) and remove inlet module (catalyst) (5). Installation Procedure
Note: When installing a new inlet module (catalyst) or a cleaned inlet module (catalyst), a DOC reset must be performed. Refer to Special Instruction, REHS8180, "Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC), and a Selective Catalyst Reduction (SCR) Filter" for the correct procedure.
Install inlet module (catalyst) (5) in the reverse order of removal.
Illustration 3 g03382086
Facing the Inlet Module Assembly.
Install clamp (1) to Dimension (Y). Dimension (Y) is 30° 5°. Tighten clamp (1) to a torque of 60 5 N m (44 4 lb ft).
Illustration 4 g03381770
Typical Example
Note: Do not use power tools in order to torque strap (2).
Apply Tooling (A) to the threads of strap (2) along Distance (Z). Distance (Z) is 25 mm (1.0 inch) above the trunnion. Tighten strap (2) to a torque of 15 + 3 - 0 N m (133 + 27 - 0 lb in).
Illustration 5 g03381887
Cutaway view of band clamp (6) in position on the assembly.
Note: Do not use power tools in order to torque band clamp (6).
Verify that the cup of the Ball Joint (G) does not touch the radius of the Ball (F). Position band clamp (6) and hand tighten band clamp (6). Band clamp (6) should be in the center of the joint.
Dimension (D) and Dimension (E) should be equal within 2.0 mm (0.08 inch). Repeat the measurements every 90° around band clamp (6). If necessary, adjust band clamp (6).
Torque band clamp (6) to a torque of 35 2 N m (26 1 lb ft).
Apply Tooling (A) to the threads of temperature sensor (3). Tighten temperature sensor (3) to a torque of 45 5 N m (33 4 lb ft).
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Nickel Anti-Seize Lubricant -
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Illustration 1 g03392235
Remove temperature sensor (3). Disconnect tube assembly (4). Loosen clamp (1) and disconnect strap (2).
Illustration 2 g03385036
Disconnect band clamp (6) and remove inlet module (catalyst) (5). Installation Procedure
Note: When installing a new inlet module (catalyst) or a cleaned inlet module (catalyst), a DOC reset must be performed. Refer to Special Instruction, REHS8180, "Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC), and a Selective Catalyst Reduction (SCR) Filter" for the correct procedure.
Install inlet module (catalyst) (5) in the reverse order of removal.
Illustration 3 g03382086
Facing the Inlet Module Assembly.
Install clamp (1) to Dimension (Y). Dimension (Y) is 30° 5°. Tighten clamp (1) to a torque of 60 5 N m (44 4 lb ft).
Illustration 4 g03381770
Typical Example
Note: Do not use power tools in order to torque strap (2).
Apply Tooling (A) to the threads of strap (2) along Distance (Z). Distance (Z) is 25 mm (1.0 inch) above the trunnion. Tighten strap (2) to a torque of 15 + 3 - 0 N m (133 + 27 - 0 lb in).
Illustration 5 g03381887
Cutaway view of band clamp (6) in position on the assembly.
Note: Do not use power tools in order to torque band clamp (6).
Verify that the cup of the Ball Joint (G) does not touch the radius of the Ball (F). Position band clamp (6) and hand tighten band clamp (6). Band clamp (6) should be in the center of the joint.
Dimension (D) and Dimension (E) should be equal within 2.0 mm (0.08 inch). Repeat the measurements every 90° around band clamp (6). If necessary, adjust band clamp (6).
Torque band clamp (6) to a torque of 35 2 N m (26 1 lb ft).
Apply Tooling (A) to the threads of temperature sensor (3). Tighten temperature sensor (3) to a torque of 45 5 N m (33 4 lb ft).
Caterpillar parts catalog:
Parts door Caterpillar catalog:
2D7342
DOOR ASSEM. (LEFT HAND)
12E, 140
12E, 140
3D5135
DOOR ASSEM.
12E, 140
12E, 140
3D2578
DOOR ASSEM.
12E, 140
12E, 140
3D2574
DOOR ASSEM.
12E, 140
12E, 140
8D2252
DOOR ASSEM.
140, 14E
140, 14E
7D0423
DOOR ASSEM.
12F, 14E
12F, 14E
3D2574
DOOR ASSEM.
12E, 140
12E, 140
3D2578
DOOR ASSEM.
12E, 140
12E, 140
3D5135
DOOR ASSEM.
12E, 140
12E, 140
2D7342
DOOR ASSEM. (LEFT HAND)
12E, 140
12E, 140