AVSPARE.COM
parts catalog

DOOR GP-CAB 5088822 - Caterpillar



5088822 DOOR GP-CAB Caterpillar parts DOOR
Rating:
11
Alternative (cross code) number:
CA5088822
508-8822
5088822
Caterpillar 5088822 DOOR GP-CAB

Buy DOOR GP-CAB 5088822 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
190-8
Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period 190-8
Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period The Electronic Control Module (ECM) can default to the secondary engine speed/timing sensor. The default will occur if a valid signal is not received from the primary engine speed/timing sensor.
The engine will shutdown only if the signals from the primary engine speed/timing sensor and the secondary engine speed/timing sensor are abnormal.
The code is logged.
637-11
Engine Timing Sensor : Other Failure Mode 261-11
Engine Timing Offset Fault The ECM has detected that the crankshaft speed/timing sensor and the camshaft speed/timing sensor are not aligned.
The code is logged.
723-8
Secondary Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period 342-8
Secondary Engine Speed Sensor : Abnormal Frequency, Pulse Width, or Period If a valid signal is not received from the secondary engine speed/timing sensor, the ECM will default to the primary engine speed/timing sensor.
The engine will shutdown only if the signals from the primary engine speed/timing sensor and the secondary engine speed/timing sensor are abnormal.
The code is logged.
4202-8
Engine Speed Sensor #3 : Abnormal Frequency, Pulse Width, or Period 2710-8
Engine Tertiary Speed Sensor : Abnormal Frequency, Pulse Width, or Period The signal from the tertiary speed/timing sensor is ignored. The engine speed is calculated by using the signal from the primary speed/timing sensor. If the signal from the primary speed/timing sensor is ignored, the engine speed is calculated by using the signal from the secondary speed/timing sensor.
4202-11
Engine Speed Sensor #3 : Other Failure Mode 2710-11
Engine Timing Offset fault The ECM has detected that the crankshaft speed/timing sensor and the camshaft speed/timing sensor are not aligned. The Electronic Control Module (ECM) uses the pattern of the pulses from the speed/timing sensors to determine the position of the crankshaft and camshaft. The ECM measures the time between the pulses that are created by the sensors as the gears rotate to determine rpm.After locating the No. 1 cylinder, the ECM triggers each injector in the correct firing order and at the correct unit injector timing. The actual timing and duration of each injection is based on engine rpm and load.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET).
B. Determine if a code is active or logged.
Codes
Result: A -8 code is active or logged.
Proceed to Test Step 2.
Result: A -11 code is active or logged.
Proceed to Test Step 6.
2. Check the Engine Speed/Timing Circuit
A. Connect Cat ET.
B. Start the engine and run the engine. The problem may occur when the engine is at any operating temperature. However, the problem is more likely to occur when the engine is at the normal operating temperature.
Circuit Check
Result: The engine started.
Proceed to Test Step 3.
Result: The engine did not start.
Proceed to Test Step 4.
3. Check for Codes
A. While the engine is running, monitor Cat ET for active codes.
B. Use Cat ET to monitor the "Engine Starting" screen for the following:
- An engine speed/timing that is "Not Detected".
Codes
Result: There is

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
953K Track-Type Loader LJT00001-UP (MACHINE) POWERED BY C7.1 Engine
963K Track-Type Loader YDR00001-UP (MACHINE) POWERED BY C7.1 Engine
953K Track-Type Loader JNR00001-UP (MACHINE) POWERED BY C7.1 Engine
973K Track-Type Loader MKL00001-UP (MACHINE) POWERED BY C9.3 Engine
963K TRACK-TYPE LOADER LBL00001-UP (MACHINE) POWERED BY C7.1 Engine


Parts door Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.