DRAWBAR AS 4713007 - Caterpillar

4713007 DRAWBAR AS Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4713007
471-3007
4713007

Weight: 6750 pounds 3061 kg.

Buy DRAWBAR AS 4713007 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Cardone 47-13007 Remanufactured Power Window Lift Motor

$143.10

18 Oct 2023
1.4[0.63] Pounds
US: Autoplicity ✅

Cardone 47-13007 Remanufactured Power Window Lift Motor
Cardone As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit || Every motor has its internal components inspected and gauged; Bushings are gauged and re-impregnated with lubricating oil, ball bearings are replaced with new and armatures are fully tested to ensure insulation || Internal gears are gauged, inspected and renewed for reuse or replaced if out of spec; Replacement gears are redesigned with a stronger, less brittle material than O.E. to prevent premature wear, stripping and breakage || Motor magnets are 100% recharged, guaranteeing efficiency and reliability; For motors which have an auto up / down feature, output signals and pulse counts are matched to the vehicle application and motors are shipped in the ‘full up position’ || Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%

$144.29

11 Oct 2023
1.4[0.63] pounds
Amazon.com

Number on catalog scheme: 7

Caterpillar 4713007 Parts scheme DRAWBAR AS

For full view, you need register

Information:

Table 1
Required Tools
Part Number Part Name Qty
8T-5096 Dial Indicator Gp 1 Face Runout (Axial Eccentricity) of the Flywheel
Illustration 1 g00286049
Checking face runout of the flywheel
Refer to illustration 1 and install the dial indicator. Always put a force on the crankshaft in the same direction before the dial indicator is read. This will remove any crankshaft end clearance.
Set the dial indicator to read 0.0 mm (0.00 inch).
Turn the flywheel at intervals of 90 degrees and read the dial indicator.
Take the measurements at all four points. Find the difference between the lower measurements and the higher measurements. This value is the runout. The maximum permissible face runout (axial eccentricity) of the flywheel must not exceed 0.15 mm (0.006 inch).Bore Runout (Radial Eccentricity) of the Flywheel
Illustration 2 g01193057
Checking bore runout of the flywheel
(1) 7H-1945 Holding Rod
(2) 7H-1645 Holding Rod
(3) 7H-1942 Dial Indicator
(4) 7H-1940 Universal Attachment
Install the 7H-1942 Dial Indicator (3). Make an adjustment of the 7H-1940 Universal Attachment (4) so that the dial indicator makes contact on the flywheel.
Set the dial indicator to read 0.0 mm (0.00 inch).
Turn the flywheel at intervals of 90 degrees and read the dial indicator.
Take the measurements at all four points. Find the difference between the lower measurements and the higher measurements. This value is the runout. The maximum permissible bore runout (radial eccentricity) of the flywheel must not exceed 0.15 mm (0.006 inch).
Illustration 3 g00286058
Flywheel clutch pilot bearing bore
Take the measurements at all four points. Find the difference between the lower measurements and the higher measurements. This value is the runout. The maximum permissible pilot bore runout of the flywheel must not exceed 0.13 mm (0.005 inch).