DRIVE GP-FINAL 1912515 - Caterpillar

1912515 DRIVE GP-FINAL Caterpillar parts 312C, 312C L

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1912515
191-2515
1912515

Buy DRIVE GP-FINAL 1912515 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

You can buy:

Travel Gearbox With Motor 191-2515 for Caterpillar CAT Engine 3054T 3064 Excavator 312 312B 312C

US$4,099.88

28 May 2025

FridayParts

Travel Gearbox With Motor 191-2515 for Caterpillar CAT Engine 3054T 3064 Excavator 312 312B 312C

Compare Prices:

As an associate, we earn commssions on qualifying purchases through the links below

$53.24

28 Dec 2019

-: -

Lenox Flex 17 8X3/4 .032 4 HR (1912515)

Caterpillar 1912515 Final Drive Replacement Caterpillar Cat 312C 312Cl 312D 312Dl 314Ccr

$6,895.00

22 Sep 2019

-: -

Caterpillar 1912515 Final Drive Replacement Caterpillar Cat 312C 312Cl 312D 312Dl 314Ccr

Show more prices Caterpillar parts

Number on catalog scheme:

Caterpillar 1912515 Parts scheme DRIVE GP-FINAL

For full view, you need register

Compatible equipment models: 1912515:

EXCAVATOR 312C 312C L Caterpillar

Information:

Diagnostic codes are associated with failed electrical components or circuits that provide information to the PRCM. Diagnostic codes are also associated with failed electrical components or circuits, that receive information from the PRCM. The diagnostic code closely identifies the cause of the failure.Each diagnostic code consists of the following items: a component identifier (CID), a failure mode identifier (FMI) and a fault indicator ("DIAG"). These items are shown on the upper display. A fault indicator can be active or inactive. The CID identifies the component that has failed in the system. The FMI describes the nature of the problem. When the "DIAG" indicator is FLASHING, the diagnostic code is active. This means that the diagnostic code is present. When the "DIAG" indicator is ON CONTINUOUSLY, the diagnostic code is inactive and the CID FMI is recorded in the fault log. See Systems Operation, "Diagnostic Code Viewing and Clearing" in order to view the fault log. When the "DIAG" indicator is not showing, there are NO diagnostic codes that are detected or recorded. Service personnel interpret the identifiers in order to assist with troubleshooting.The PRCM has a fault log to help with troubleshooting of diagnostic codes. Inactive diagnostic codes (CID FMI) are recorded in the fault log for viewing at a later time. Also, the number of occurrences are totalled and the number of occurrences are shown on the upper display with the CID and the FMI. During troubleshooting, it is sometimes necessary to disconnect the harness connector from the PRCM and a diagnostic code of CID 0590 FMI 09 is created. An FMI 09 describes the voltage that is above normal. This fact is also used as an aid in the troubleshooting process. Clear these created diagnostic codes after the particular problem is corrected and the diagnostic code is cleared.Note: The CID 590 FMI 09 will NOT be logged if the setpoint "P03" is set to "01". Refer to Systems Operation, "Setpoint Viewing and Programming".
Table 1
DIAGNOSTIC CODES for the PRCM
For troubleshooting, see the procedure with the same CID and FMI.
CID / FMI Description
CID 0248 CAT data link:
FMI 11 Short to + Battery or a short to - B of either CAT data link wire.
CID 0268 PRCM Internal Memory:
FMI 02 Signal out of range.
CID 0333 Relay Driver Module (A):
FMI 03 Voltage above normal.
FMI 04 Voltage below normal.
CID 0334 Relay Driver Module (B):
FMI 03 Voltage above normal.
FMI 04 Voltage below normal.
CID 0477 PRCM Output Relay (1):
FMI 03 Relay coil open circuit.
FMI 04 Relay