1914931 DRIVE GP-FINAL Caterpillar parts
D5R LGP, D6N, D6N LGP
Rating:
Alternative (cross code) number:
CA1914931
191-4931
1914931
CA1914931
191-4931
1914931
Weight: 837 pounds 379 kg.
TRACK-TYPE TRACTOR,
Number on catalog scheme:
For full view, you need register
Information:
is connected to pin 1 of the emergency stop switch. The other end of this conductor is connected to pin 86 of the PECM relay. Remove the terminal from pin 86 of this relay. Remove this entire conductor from the existing harness.
If the EIP does NOT contain the ISDR, go to Step 15. If the EIP does have an ISDR, continue with this step. Locate the ISDR and remove any terminal lugs that are connected to pins 30 and 87 of the ISDR. The other end of the conductor that is connected to pin 30 of the ISDR is connected to pin 1 of the emergency stop button. Remove this terminal lug from pin 1 of the emergency stop button. Remove this conductor from the existing harness.
Remove the terminal that is connected to pin 87A of the ISDR. The other end of this conductor is connected to pin 86 of the PECM relay. Disconnect the terminal from pin 86 of the PECM relay and from pin 86 of the SECM relay. Remove this entire conductor from the existing harness.
Connect the leads with the labels "ES-8 ISDR-87" and "ISDR-30 ESLR-87" from the new harness to pins 87 and 30 of the ISDR. Connect the conductors to pin 8 and ESLR pin 87 on the emergency stop switch. Connections will be made to pins 86 of the PECM relay and the SECM relay in a later step.
Illustration 10 g00656824
(9) 9X-8248 Heat Tube
Locate the shutdown notify relay. Remove the terminal lug that is attached to pin 85 of the relay. Slide a 65 mm (2.5 inch) length of 9X-8248 Heat Tube (9) over this wire. Connect the male terminal lug from the new harness to the female lug that was removed from pin 85 of the shutdown notify relay.
Slide the heat shrink tubing over both terminal lugs. Heat the tube until a tight seal is formed.
Connect the lead with the label "ESLR-85 SDNR-85" to pin 85 of the shutdown notify relay.
Locate the PECM relay and the SECM relay. Connect the new harness conductor with the label "ESR-87A PECMR-86" to pin 86 of the PECM relay. Connect the new harness conductor with the label "PECMR-86 SECMR-86" to pin 86 of the SECM relay.
Illustration 11 g00656847
(10) ES-1 ESR-30 Conductor, connect to pin 1 of the Emergency Stop Switch (11) EMSS-20 ES-7 Conductor, connect to pin 20 of the Engine Control Switch
Locate the rear of the ECS. Remove the screw on terminal 20 of the switch. Connect the new harness conductor (11) with the label "EMSS-20 ES-7" to pin 20 of the ECS. Install and tighten the screw on terminal 20.
Locate the new emergency stop switch block. The emergency stop switch block is attached to at least two leads of the new harness. There will be an additional lead with the label "ES-1" at the same point of the harness. Connect the conductor (10) with the label "ES-1 ESR-30" to pin 1 of the emergency stop switch. The new emergency stop switch block
If the EIP does NOT contain the ISDR, go to Step 15. If the EIP does have an ISDR, continue with this step. Locate the ISDR and remove any terminal lugs that are connected to pins 30 and 87 of the ISDR. The other end of the conductor that is connected to pin 30 of the ISDR is connected to pin 1 of the emergency stop button. Remove this terminal lug from pin 1 of the emergency stop button. Remove this conductor from the existing harness.
Remove the terminal that is connected to pin 87A of the ISDR. The other end of this conductor is connected to pin 86 of the PECM relay. Disconnect the terminal from pin 86 of the PECM relay and from pin 86 of the SECM relay. Remove this entire conductor from the existing harness.
Connect the leads with the labels "ES-8 ISDR-87" and "ISDR-30 ESLR-87" from the new harness to pins 87 and 30 of the ISDR. Connect the conductors to pin 8 and ESLR pin 87 on the emergency stop switch. Connections will be made to pins 86 of the PECM relay and the SECM relay in a later step.
Illustration 10 g00656824
(9) 9X-8248 Heat Tube
Locate the shutdown notify relay. Remove the terminal lug that is attached to pin 85 of the relay. Slide a 65 mm (2.5 inch) length of 9X-8248 Heat Tube (9) over this wire. Connect the male terminal lug from the new harness to the female lug that was removed from pin 85 of the shutdown notify relay.
Slide the heat shrink tubing over both terminal lugs. Heat the tube until a tight seal is formed.
Connect the lead with the label "ESLR-85 SDNR-85" to pin 85 of the shutdown notify relay.
Locate the PECM relay and the SECM relay. Connect the new harness conductor with the label "ESR-87A PECMR-86" to pin 86 of the PECM relay. Connect the new harness conductor with the label "PECMR-86 SECMR-86" to pin 86 of the SECM relay.
Illustration 11 g00656847
(10) ES-1 ESR-30 Conductor, connect to pin 1 of the Emergency Stop Switch (11) EMSS-20 ES-7 Conductor, connect to pin 20 of the Engine Control Switch
Locate the rear of the ECS. Remove the screw on terminal 20 of the switch. Connect the new harness conductor (11) with the label "EMSS-20 ES-7" to pin 20 of the ECS. Install and tighten the screw on terminal 20.
Locate the new emergency stop switch block. The emergency stop switch block is attached to at least two leads of the new harness. There will be an additional lead with the label "ES-1" at the same point of the harness. Connect the conductor (10) with the label "ES-1 ESR-30" to pin 1 of the emergency stop switch. The new emergency stop switch block
Caterpillar SIS machinery equipment:
Caterpillar SIS
D6N XL, D/S, LGP TRACK-TYPE TRACTOR AKM00001-UP (MACHINE) POWERED BY 3126B Engine »
191-4931
DRIVE GP-FINAL
D6N TRACK-TYPE TRACTOR XL Differential Steering CCK00001-UP (MACHINE) POWERED BY 3126B Engine »
191-4931
DRIVE GP-FINAL
D6N TRACK-TYPE TRACTOR XL, LGP Differential Steering DJA00001-UP (MACHINE) POWERED BY C6.6 Engine »
191-4931
DRIVE GP-FINAL
D6N TRACK-TYPE TRACTOR XL JAH00001-UP (MACHINE) POWERED BY C6.6 Engine »
191-4931
DRIVE GP-FINAL
D6N XL, LGP Differential Steering, Electrohydraulic Implement TRACK-TYPE TRACTOR GHS00001-UP (MACHINE) POWERED BY C6.6 Engine »
191-4931
DRIVE GP-FINAL
D6N XL Differential Steering, Electrohydraulic Implement TRACK-TYPE TRACTOR LJR00001-UP (MACHINE) POWERED BY C6.6 Engine »
191-4931
DRIVE GP-FINAL
D6N TRACK-TYPE TRACTOR XL, LGP PBA00001-UP (MACHINE) POWERED BY C6.6 Engine »
191-4931
DRIVE GP-FINAL
D5R XL, LGP Differential Steering, Electrohydraulic Implement TRACK-TYPE TRACTOR D5L00001-UP (MACHINE) POWERED BY C6.6 Engine »
191-4931
DRIVE GP-FINAL
D6N TRACK-TYPE TRACTOR XL, LGP GB600001-UP (MACHINE) POWERED BY C7.1 Engine »
191-4931
DRIVE GP-FINAL
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CBL00001-UP (MACHINE) POWERED BY 3126B ENGINE »
191-4931
FINAL DRIVE GROUP
D6N TRACK-TYPE TRACTOR PS DS XL/PS DS LGP CBL00001-UP (MACHINE) POWERED BY 3126B ENGINE »
191-4931
FINAL DRIVE GROUP
Caterpillar parts catalog:
Parts drive Caterpillar catalog:
2676431
DRIVE GP-FAN
D5R LGP, D6N
D5R LGP, D6N
1892203
DRIVE GP-FAN
561N, 953C, 963C, D5N, D6N
561N, 953C, 963C, D5N, D6N
3487311
DRIVE GP-FAN
D6N LGP, D6N OEM
D6N LGP, D6N OEM
1914932
DRIVE GP-FINAL
D5R LGP, D6N, D6N LGP, D6N OEM
D5R LGP, D6N, D6N LGP, D6N OEM
2261415
DRIVE GP-FINAL
D6N, D6N LGP
D6N, D6N LGP
2288812
DRIVE GP-FINAL
D6N, D6N LGP
D6N, D6N LGP
3485000
DRIVE GP-FAN
D6N LGP, D6N OEM
D6N LGP, D6N OEM
1433438
DRIVE
D5M, D5N, D6M, D6N
D5M, D5N, D6M, D6N
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 135H, 135H NA, 140G, 140K, 140K 2, 160K, 214B, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 32...
D6N LGP
3528148
DRIVE GP-FINAL
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314D CR, 314D LCR, 314E CR, 314E LCR
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314D CR, 314D LCR, 314E CR, 314E LCR
4239923
DRIVE GP-CIRCLE
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD
2208623
DRIVE GP-SWING
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 511, 521, 521B, 522, 522B, 532, TK711, TK721, TK722, TK732
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 511, 521, 521B, 522, 522B, 532, TK711, TK721, TK722, TK732
9S4074
DRIVE GP-PUMP
824B, 825B, 826B, 834, 988
824B, 825B, 826B, 834, 988
1079542
DRIVE GP-FAN
12H, 12H ES, 12H NA, 140H ES, 140H NA, 143H, 160H ES, 160H NA
12H, 12H ES, 12H NA, 140H ES, 140H NA, 143H, 160H ES, 160H NA
1862949
DRIVE GP-FINAL
D9R, D9T
D9R, D9T
318E L, 319D L, 319D LN, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D2 L, 323E L
1809511
DRIVE GP-FAN
3126B, 3126E
3126B, 3126E
1278573
DRIVE GP-DRUM
CB-634C
CB-634C
6G5549
DRIVE GP-CIRCLE
12G, 130G, 140G
12G, 130G, 140G
2229216
DRIVE GP-FINAL
D6R III, D6T
D6R III, D6T