AVSPARE.COM
parts catalog

DRUM GP-HOPPER 5088331 - Caterpillar



5088331 DRUM GP-HOPPER Caterpillar parts DRUM
Rating:
46
Alternative (cross code) number:
CA5088331
508-8331
5088331
Caterpillar 5088331 DRUM GP-HOPPER

Buy DRUM GP-HOPPER 5088331 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 4
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     311-1362     Vacuum Cap     1    
B     5F-7345     Screw     1    
5P-7344 Block     1    
- Bolts (M8)     2    
C     -     Loctite 242     -    
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes to prevent fluid loss and keep contaminants from entering the system.
Release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure - Release".
Illustration 1 g01368952
Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A) . Apply 138 kPa (20 psi). This procedure will pull a vacuum on the hydraulic system.
Illustration 2 g02362296
Remove guard (1) .
Illustration 3 g02362299
Remove guard (2) .
Illustration 4 g02362317
Remove fan (3) .
Illustration 5 g02362297
Remove nut (4) .
Illustration 6 g02362336
Install Tooling (A) in order to remove adapter (5) .
Illustration 7 g02362338
Remove clips (6) . Disconnect hose assemblies (7) , (8) , and (9) .
Illustration 8 g02362356
Remove gear motor (10) .Installation Procedure
Install fan and gear motor (10) in the reverse order as the removal.
Apply Tooling (C) to the shaft threads of gear motor (10) .

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
BD118 & BD121 Side Discharge Buckets BND00001-UP (MACHINE)


Parts drum Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.