1049634 EDGE-CUTTING Caterpillar parts
D4C III, D4G
Rating:
Alternative (cross code) number:
CA1049634
104-9634
1049634
CA1049634
104-9634
1049634
Weight: 39 pounds 17 kg.
Information:
ABRASION RESISTANT MATERIAL
N
BOLT HOLE SIZE
18
mm
CHAMFER
EDGE
HOLE PATTERN
CENTERLINE
HOLE SPACING
152.4
mm
LENGTH
975.6
mm
NUMBER OF HOLES
6
THICKNESS
16
mm
TUNGSTEN CARBIDE
N
WIDTH
165
mm
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Replacement for fits 1049634 New Cutting Edge Fits Several Fits Caterpillar Fits CAT Models
Jinzhirullx
Jinzhirullx
RAParts 1049634 Fits Caterpillar Cutting Edge fits Several Models
Reliable Aftermarket Parts One New Aftermarket Replacement Cutting Edge That Fits Caterpillar Models. Replaces Part Number: Dbd || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
Reliable Aftermarket Parts One New Aftermarket Replacement Cutting Edge That Fits Caterpillar Models. Replaces Part Number: Dbd || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
Number on catalog scheme:
2
For full view, you need register
Information:
Probable Causes
Air inlet or exhaust system
Atmospheric pressure sensor
Flash file
Fuel quality
Valve adjustmentRecommended Actions
Table 1
Troubleshooting Test Steps Values Results
1. Check the Air Inlet System for Restrictions and/or for Leaks
A. Check for an air filter restriction.
B. Perform a visual inspection of the system for restrictions and/or for leaks in the air inlet piping .
C. Ensure that the turbocharger is in good repair.
Air Inlet System
Result: The air inlet system is NOT OK.
Repair: Repair or replace any worn or damaged components.
Result: The air inlet system is OK.
Proceed to Test Step 2.
2. Check the Atmospheric Pressure Sensor
A. Check the Caterpillar Electronic Technician (ET) for active diagnostic codes on the sensor. If no active diagnostic code exists, the sensor may be used.
50 kPa (7.25 psi) and 100 kPa (14.5 psi)
Result: The atmospheric pressure sensor is NOT OK.
Repair: Replace the atmospheric pressure sensor.
Result: The atmospheric pressure sensor is OK.
Proceed to Test Step 3.
3. Check the Flash File
A. Verify that the latest flash file is installed. Refer to Troubleshooting, "ECM Software - Install" for information.
Flash File
Result: The correct flash file is not found.
Repair: Download and install the correct flash file.
Result: The correct flash file is found.
Proceed to Test Step 4.
4. Check the Fuel Quality
A. Cold weather adversely affects the characteristics of the fuel. Refer to Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation.
Fuel Quality
Result: The fuel quality is poor.
Repair: Replace the fuel in the fuel tank.
Result: The fuel quality is OK.
Proceed to Test Step 5.
5. Check the Valve Adjustment
A. Refer to Systems Operation/Testing and Adjusting for information that is related to valve adjustments.
Valve Adjustment
Result: The valve adjustment is NOT OK.
Repair: Adjust the valves. Refer to Testing and Adjusting for more information on adjusting the valves.
STOP
Air inlet or exhaust system
Atmospheric pressure sensor
Flash file
Fuel quality
Valve adjustmentRecommended Actions
Table 1
Troubleshooting Test Steps Values Results
1. Check the Air Inlet System for Restrictions and/or for Leaks
A. Check for an air filter restriction.
B. Perform a visual inspection of the system for restrictions and/or for leaks in the air inlet piping .
C. Ensure that the turbocharger is in good repair.
Air Inlet System
Result: The air inlet system is NOT OK.
Repair: Repair or replace any worn or damaged components.
Result: The air inlet system is OK.
Proceed to Test Step 2.
2. Check the Atmospheric Pressure Sensor
A. Check the Caterpillar Electronic Technician (ET) for active diagnostic codes on the sensor. If no active diagnostic code exists, the sensor may be used.
50 kPa (7.25 psi) and 100 kPa (14.5 psi)
Result: The atmospheric pressure sensor is NOT OK.
Repair: Replace the atmospheric pressure sensor.
Result: The atmospheric pressure sensor is OK.
Proceed to Test Step 3.
3. Check the Flash File
A. Verify that the latest flash file is installed. Refer to Troubleshooting, "ECM Software - Install" for information.
Flash File
Result: The correct flash file is not found.
Repair: Download and install the correct flash file.
Result: The correct flash file is found.
Proceed to Test Step 4.
4. Check the Fuel Quality
A. Cold weather adversely affects the characteristics of the fuel. Refer to Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold-weather operation.
Fuel Quality
Result: The fuel quality is poor.
Repair: Replace the fuel in the fuel tank.
Result: The fuel quality is OK.
Proceed to Test Step 5.
5. Check the Valve Adjustment
A. Refer to Systems Operation/Testing and Adjusting for information that is related to valve adjustments.
Valve Adjustment
Result: The valve adjustment is NOT OK.
Repair: Adjust the valves. Refer to Testing and Adjusting for more information on adjusting the valves.
STOP
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
1402188
EDGE GP-BIT & CUTTING
D4C III
D4C III
1792897
EDGE GP-BIT & CUTTING
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL
1049631
EDGE GP-BIT & CUTTING
D4C III, D4G
D4C III, D4G
311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, D4C III
315C, 315D L, D4C II, D4C III, D5C III, D5G
D3B, D3C II, D3C III, D3G, D4G, D5G
D3B, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5K LGP, D5K2 XL
1412239
EDGE GP-BIT
D4C III
D4C III
1412238
EDGE-CUTTING
D4C III
D4C III
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL
1412238
EDGE-CUTTING
D4C III
D4C III
1412239
EDGE GP-BIT
D4C III
D4C III
1410413
EDGE-CUTTING
D3C III
D3C III
D3B, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5K LGP, D5K2 XL
D3B, D3C II, D3C III, D3G, D4G, D5G
525C, 525D, 535C, 535D, 545, 545C, 545D, 555D, D4H XL, D5M, D5N, D6K, D6K LGP, D6K XL
8Y5291
EDGE
931C II, 933, 935C II
931C II, 933, 935C II
8Y4738
EDGE
931C II, 933, 933C, 935C II
931C II, 933, 933C, 935C II
5G3477
EDGE-CUTTING
931B, 933, 933C
931B, 933, 933C
517, D4H, D4HTSK II, D4HTSK III, D5C, D5C III, D5G
D5C III
1400934
EDGE GP-BIT & CUTTING
D5C III
D5C III