1285366 EDGE AS Caterpillar parts
322B L, 322C, 325B L, 325C, 330B, 330B L, 330C, 330C L
Rating:
Alternative (cross code) number:
CA1285366
128-5366
1285366
CA1285366
128-5366
1285366
Weight: 634 pounds 287 kg.
EXCAVATOR,
Compatible equipment models: 1285366:
Number on catalog scheme:
4
For full view, you need register
Information:
Introduction
This special instruction contains the procedure to install the position sensor group. The new sensor has more reliability.Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Safety Section
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Caterpillar dealer for replacement manuals. Proper care is your responsibility.
Personal injury or death can result from improper assembly procedures.Do not attempt any assembly until you have read and understand the assembly instructions.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Required Parts
Table 1
Required Parts List
Item Qty Part Number Part Name
1 2 369-9618 Position Sensor Gp Installation Procedure
Illustration 1 g06150642
(1) 369-9618 Position Sensor Gp
(A) Displacement pump #1
(B) Displacement pump #2
Illustration 2 g06132946
Check the error code log from the monitor. Select “Service” (Input service password) – “Diagnostic” – “Logged Diagnostic Codes”.
Illustration 3 g06132947
If there is error code 2899 and/or 2900, replace the sensor with new one. Error code 2899 for Pump #1 (A) sensor, 2900 for Pump #2 (B) sensor.
Illustration 4 g06150697
(1) 369-9618 Position Sensor Gp
(C) Sensor guard
(D) BoltNote: In case 458-6031 Position Sensor Gp is ordered, no need to replace 448-1451 Sensor with the new sensor which is located inside of the pump.
Remove sensor and sensor guard (C) with bolts (D). Install new sensor (1) and sensor guard (C) with bolts (D). Tighten the bolts to 12 3 N m (106 26 lb in).
Refer to KENR9615 / , KENR9995 to perform the calibration.
This special instruction contains the procedure to install the position sensor group. The new sensor has more reliability.Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Safety Section
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Caterpillar dealer for replacement manuals. Proper care is your responsibility.
Personal injury or death can result from improper assembly procedures.Do not attempt any assembly until you have read and understand the assembly instructions.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Required Parts
Table 1
Required Parts List
Item Qty Part Number Part Name
1 2 369-9618 Position Sensor Gp Installation Procedure
Illustration 1 g06150642
(1) 369-9618 Position Sensor Gp
(A) Displacement pump #1
(B) Displacement pump #2
Illustration 2 g06132946
Check the error code log from the monitor. Select “Service” (Input service password) – “Diagnostic” – “Logged Diagnostic Codes”.
Illustration 3 g06132947
If there is error code 2899 and/or 2900, replace the sensor with new one. Error code 2899 for Pump #1 (A) sensor, 2900 for Pump #2 (B) sensor.
Illustration 4 g06150697
(1) 369-9618 Position Sensor Gp
(C) Sensor guard
(D) BoltNote: In case 458-6031 Position Sensor Gp is ordered, no need to replace 448-1451 Sensor with the new sensor which is located inside of the pump.
Remove sensor and sensor guard (C) with bolts (D). Install new sensor (1) and sensor guard (C) with bolts (D). Tighten the bolts to 12 3 N m (106 26 lb in).
Refer to KENR9615 / , KENR9995 to perform the calibration.
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
311C, 311D LRR, 311F LRR, 312C L, 312D, 314C, 314D LCR, 315C, 315D L, 320C, 322C, 325B L, D6E, D6E SR, D6G, D6G SR, D6G2 XL, D6T XL
315C, 320C, 322C, 325B L, 924G, 924GZ, 924H, 924K, 928HZ, 930G, 930K, 938K
1934884
EDGE AS
325C, 330C L
325C, 330C L
1934950
EDGE AS
330C L
330C L
2025141
EDGE AS
330C L
330C L
1276877
EDGE AS
330B L, 330C L
330B L, 330C L
1276872
EDGE AS
330B L, 330C L
330B L, 330C L
2717296
EDGE AS
330C L
330C L
2717297
EDGE AS
330C L
330C L
2773890
EDGE AS
330C L
330C L
1285390
EDGE
330C L
330C L
1235392
EDGE AS
325B, 330B
325B, 330B
1282954
EDGE AS
322B L, 322C, 325B L, 325C, 330B L, 330C L
322B L, 322C, 325B L, 325C, 330B L, 330C L
1052532
EDGE AS
322B L, 322C, 325, 325B L, 325C, 330, 330 FM L, 330B L, 330C L
322B L, 322C, 325, 325B L, 325C, 330, 330 FM L, 330B L, 330C L
1272296
EDGE AS
320B, 320C, 322 FM L, 322B L, 322B LN, 322C, 325, 325B L, 325C, 330, 330B L
320B, 320C, 322 FM L, 322B L, 322B LN, 322C, 325, 325B L, 325C, 330, 330B L
1379527
EDGE
322B L, 325, 325B L
322B L, 325, 325B L
1045748
EDGE AS
322B L, 322C, 325, 325B L, 325C, 330, 330 FM L, 330B L, 330C L
322B L, 322C, 325, 325B L, 325C, 330, 330 FM L, 330B L, 330C L
6I5224
EDGE AS
322B L, 322C, 325, 325 L, 325 LN, 325B L, 325C, 330, 330 FM L, 330B L, 330C, 330C L
322B L, 322C, 325, 325 L, 325 LN, 325B L, 325C, 330, 330 FM L, 330B L, 330C, 330C L
1358634
EDGE
322 FM L, 322B L, 322C
322 FM L, 322B L, 322C
6I5193
EDGE AS
320 L, 320B, 320C, 322 FM L, 322B L, 322C, 325, 325 L, 325B, 325B L, 325C, 330, 330 FM L, 330B L
320 L, 320B, 320C, 322 FM L, 322B L, 322C, 325, 325 L, 325B, 325B L, 325C, 330, 330 FM L, 330B L
1328418
EDGE AS
322 FM L, 322B L, 322C, 325B L, 325C, 330, 330 FM L, 330B L
322 FM L, 322B L, 322C, 325B L, 325C, 330, 330 FM L, 330B L
1052761
EDGE AS
320C, 322 FM L, 322B L, 322C, 325, 325B L, 325C, 330, 330 FM L, 330B L
320C, 322 FM L, 322B L, 322C, 325, 325B L, 325C, 330, 330 FM L, 330B L
1295714
EDGE AS
320B, 320C, 320C L, 320D, 320D L, 322 FM L, 322B L, 322C, 323D L, 324D, 324D L, 325B L, 325C, 330B L
320B, 320C, 320C L, 320D, 320D L, 322 FM L, 322B L, 322C, 323D L, 324D, 324D L, 325B L, 325C, 330B L
1285389
EDGE AS
322B L, 322C, 325B L, 325C, 330B L, 330C L
322B L, 322C, 325B L, 325C, 330B L, 330C L