EDGE-CUTTING 1577338 - Caterpillar

Operator Level Inducement
Inducements are engine derates, vehicle speed limits, or other actions intended to prompt the operator to repair or maintain the emissions control system.Inducement strategies are control actions required by EPA/ARB Tier 4 final and EU Stage IV regulations to ensure prompt correction of various failures in the engine NOx emissions control system. They require actions to limit engine performance and define required indications such as visual alarms including lamps and messages, as well as audible alarms, while the control actions are imposed.
Table 1
J1939 Code and Description CDL Code and Description Comments
5246-0
Aftertreatment SCR Operator Inducement Severity : High - most severe (3) E1389 (3)
Aftertreatment #1 SCR Operator Inducement This code is a Level 3 inducement associated with an emissions system fault. The engine is derated 100%, limited to low idle or 1000 RPM, and can experience 5 minute rolling shutdowns.
5246-15
Aftertreatment SCR Operator Inducement Severity : High - least severe (1) E1389 (1)
Aftertreatment #1 SCR Operator Inducement This code is a Level 1 inducement associated with an emissions system fault.
5246-16
Aftertreatment SCR Operator Inducement Severity : High - moderate severity (2) E1389 (2)
Aftertreatment #1 SCR Operator Inducement This code is a Level 2 inducement associated with an emissions system fault. Refer to Systems Operation, "DEF Dosing Control System" for details on inducement configuration options and inducement actions.Associated Codes
Troubleshoot any associated diagnostic codes listed in Table 2 that are present. Refer to "Inducement Type" in Table 2 for the correct Inducement table.
Table 2
Associated Codes
J1939 Code and Description CDL Code and Description Inducement Category
1231-9
J1939 Network #2 : Abnormal Update Rate 2348-9
SAE J1939 Data Link #2 : Abnormal Update Rate Category 1
1231-14
J1939 Network #2 : Special Instruction 2348-14
SAE J1939 Data Link #2 : Special Instruction Category 2
1235-9
J1939 Network #3 : Abnormal Update Rate 5856-9
SAE J1939 Data Link #3 : Abnormal Update Rate Category 1
1235-14
J1939 Network #3 : Special Instruction 5856-14
SAE J1939 Data Link #3 : Special Instruction Category 2
1761-3
Aftertreatment #1 DEF Tank Volume #1 : Voltage Above Normal 3130-3
Aftertreatment #1 DEF Tank #1 Level Sensor : Voltage Above Normal Category 1
1761-4
Aftertreatment #1 DEF Tank Volume #1 : Voltage Below Normal 3130-4
Aftertreatment #1 DEF Tank #1 Level Sensor : Voltage Below Normal Category 1
2659-17
EGR Mass Flow Rate : Low - least severe (1) E1095 (1)
Low EGR Mass Flow Rate Category 3
2791-5
EGR Valve Control : Current Below Normal 3405-5
EGR Valve Control : Current Below Normal Category 3
3031-7
Aftertreatment #1 DEF Tank Temperature : Not Responding Properly E1441 (2)
Aftertreatment #1 DEF Tank Temperature #1 Not Responding Category 1
3031-16
Aftertreatment #1 DEF Tank Temperature : High - moderate severity (2) E960 (2)
High Aftertreatment #1 DEF Tank Temperature #1 Category 2
3031-18
Aftertreatment #1 DEF Tank Temperature : Low - moderate severity (2) E1398 (2)
Low Aftertreatment #1 DEF Tank Temperature #1 Category 2
3216-7
Aftertreatment #1 Intake NOx : Not Responding Properly E1431 (2)
Invalid Aftertreatment #1 Intake NOx Level #1 Category 2
3216-11
Aftertreatment #1 Intake NOx : Other Failure Mode 3655-11
Aftertreatment #1 Intake NOx Level Sensor : Other Failure Mode Category 2
3216-12
Aftertreatment #1 Intake NOx : Failure 3655-12
Aftertreatment #1 Intake NOx Level Sensor :