2500564 EDGE AS Caterpillar parts
320C, 322B L, 322C
Rating:
Alternative (cross code) number:
CA2500564
250-0564
2500564
CA2500564
250-0564
2500564
EXCAVATOR,
Number on catalog scheme:
1
For full view, you need register
Information:
Illustration 17 g06206863
(10) Side plate
(11) Bevel
(12) Plate #2
(13) Tack weld
Make bevel around the hole by grinding and install the Plate #2 with tack weld.
Illustration 18 g06206869
(14) Weld
(15) Plate #3
(16) GrindingNote: Maximum grinding undercut permitted is 0.8 mm (0.03 inch).
Weld the Plate #3. Grind the weld joint surface. If required grind the Plate #3 to adjust the hole size and shape.
Illustration 19 g06206883
(18) Plate #4
Illustration 20 g06206886
(17) Detail view
Illustration 21 g06206892
(19) Notch is not permitted
(20) Plate #4Note: Top plate notch is not permitted from G to H.Note: The top plate and the side plate weld joint should be smooth. Grind the surface after burying a triangular part. Refer to Illustration 20.Note: Plate #4 should be added to both the side of the boom even though the second hole is not made.
Weld all around the Plate #4 and grind the surface. If required grind the Plate #4 to adjust the size.
Illustration 22 g06206927
(21) Stud
(22) Plate
(23) Support plate
Remove the eight studs, two plates and two support plates from the top plate. Reuse the clips, washers, and nuts on the stud.
Illustration 23 g06206933
Support plate installation dimension
Note: Welding is not permitted within 10 mm (0.4 inch) from the edge.
Reinstall the two support plates (23).
Illustration 24 g06206946
Plate #5 welding dimension
(24) Plate #5
Illustration 25 g06206951
Detail view of area (25)
Note: The top plate and the side plate weld joint should be smooth. Grind the surface after burying a triangular part. Refer to Illustration 25.
Weld all around the Plate #5 and grind the surface. If required grind the Plate #5 to adjust the size.
Illustration 26 g06206960
Grinding area
Illustration 27 g06206989
(26) As weld
(27) After grinding (side view)
(28) After grinding (top view)
Grind the area M to N and make the surface smooth. Grind the area P to R and make the surface smooth.
Illustration 28 g06207000
(29) Stud
(30) Plate
Weld the six 117-5604 Studs and two 087-5841 Plates. Refer to Illustration 28 for the dimension.
Illustration 29 g06207009
(31) Plate #5
(32) 117-5604 Studs
Weld the four 117-5604 Studs to avoid harness interference with the Plate #5. Install the clip, washer, and nut.
Clean and paint the worked area.
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
311C, 311D LRR, 311F LRR, 312C L, 312D, 314C, 314D LCR, 315C, 315D L, 320C, 322C, 325B L, D6E, D6E SR, D6G, D6G SR, D6G2 XL, D6T XL
315C, 320C, 322C, 325B L, 924G, 924GZ, 924H, 924K, 928HZ, 930G, 930K, 938K
320C, 630B, 631B, 631D, 631G, 637, 637B, 637D, 637E, 637G, 9A
320C
2584576
EDGE AS
322C, 325B L, 325C, 330C L
322C, 325B L, 325C, 330C L
2584577
EDGE AS
322C, 325B L, 325C, 330C L
322C, 325B L, 325C, 330C L
2584578
EDGE AS
322C, 325B L, 325C, 330C L
322C, 325B L, 325C, 330C L
2794110
EDGE AS
322C, 324D, 324D L, 324E LN, 325B L, 325C, 325D L, 329D L, 329E LN, 330C L, 330D L, 336D L, 336E L
322C, 324D, 324D L, 324E LN, 325B L, 325C, 325D L, 329D L, 329E LN, 330C L, 330D L, 336D L, 336E L
2794111
EDGE AS
322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330C L, 330D L, 336D L, 336E L
322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330C L, 330D L, 336D L, 336E L
2794112
EDGE AS
322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330C L, 330D L, 336D L, 336E L
322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330C L, 330D L, 336D L, 336E L
2794117
EDGE AS
322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330C L, 330D L, 336D L, 336D2, 336E L
322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330C L, 330D L, 336D L, 336D2, 336E L
2794113
EDGE AS
322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330C L, 330D L, 336D L, 336D2, 336E L, 336E LH, 336F L
322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330C L, 330D L, 336D L, 336D2, 336E L, 336E LH, 336F L
2500563
EDGE AS
320C, 322B L, 322C
320C, 322B L, 322C
2500562
EDGE AS
320C, 322B L, 322C
320C, 322B L, 322C
2500561
EDGE AS
320C, 322B L, 322C
320C, 322B L, 322C
2500560
EDGE AS
320C, 322B L, 322C
320C, 322B L, 322C
2500559
EDGE AS
320C, 322B L, 322C
320C, 322B L, 322C
2409607
EDGE AS
322B L, 322C, 324D L
322B L, 322C, 324D L
2416727
EDGE AS
320C, 322B L, 322C
320C, 322B L, 322C
2416726
EDGE AS
320C, 322B L, 322C, 325B L, 325C
320C, 322B L, 322C, 325B L, 325C
2416725
EDGE AS
320C, 322B L, 322C
320C, 322B L, 322C
2049719
EDGE AS
322B L, 322C, 325B L, 325C, 330B L
322B L, 322C, 325B L, 325C, 330B L
2049717
EDGE AS
322B L, 322C, 325B L, 325C, 330B L
322B L, 322C, 325B L, 325C, 330B L
2049714
EDGE AS-CUTTING
322B L, 322C, 325C, 330B L, 330C L
322B L, 322C, 325C, 330B L, 330C L