EDGE AS 2553759 - Caterpillar

Illustration 3 g01634575
Rear view (17) Torque for two nuts ... 10 1 N m (90 9 lb in) (18) Torque for the breather assembly ... 54 3 N m (40 2 lb ft) (19) Torque for four plug assemblies ... 54 3 N m (40 2 lb ft) (20) Torque for the plug ... 54 3 N m (40 2 lb ft) (21) Torque for the bolt ... 88 4 N m (65 3 lb ft) (22) Torque for 14 bolts ... 65 3 N m (48 2 lb ft)
Illustration 4 g01634574
Section H-H (23) Use the following procedure to tighten four bolts:
Tighten the bolts in a crisscross sequence by 7 N m (60 lb in) increments.
Again, tighten the bolts in a crisscross sequence to a final torque of 27 3 N m (240 27 lb in). (24) Thickness of five new friction discs and five new clutch discs for the forward clutch and reverse clutch is 19.40 0.65 mm (0.764 0.026 inch). Thickness of one new 6Y-7929 Friction Disc ... 2.05 0.08 mm (0.081 0.003 inch) Minimum thickness of one worn 6Y-7929 Friction Disc ... 1.62 mm (0.064 inch) Thickness of one new 274-4553 Clutch Disc ... 1.78 to 1.88 mm (0.070 to 0.074 inch) (25) The surfaces must be clean, free from oil and grease. Before assembly, apply 6V-6640 Sealant to the mating surfaces of front transmission case and rear transmission case. (26) As required, use the following shims in order to obtain an end play of 0.03 to 0.08 mm (0.001 to 0.003 inch). All the shims must be located against the bearing cup of the rear transmission case. The 7T-3034 Spacer must be in contact with the rear transmission case. 7T-3034 Spacer Quantity ... 1 Thickness of the spacer ... 1.98 to 2.02 mm (0.078 to 0.080 inch) Outside diameter ... 64.5 mm (2.54 inch) 6T-9144 Shim Quantity ... 1 Thickness of the shim ... 0.05 mm (0.002 inch) Outside diameter ... 64.5 mm (2.54 inch) 6T-9147 Shim Quantity ... 1 Thickness of the shim ... 0.08 mm (0.003 inch) Outside diameter ... 64.5 mm (2.54 inch) 6T-9146 Shim Quantity ... 1 Thickness of the shim ... 0.13 mm (0.005 inch) Outside diameter ... 64.5 mm (2.54 inch) 6T-9145 Shim Quantity ... 1 Thickness of the shim ... 0.18 mm (0.007 inch) Outside diameter ... 64.5 mm (2.54 inch) 6T-9143 Shim Quantity ... 1 Thickness of the shim ... 0.38 mm (0.015 inch) Outside diameter ... 64.5 mm (2.54 inch) 6T-9142 Shim Quantity ... 1 Thickness of the shim ... 0.51 mm (0.020 inch) Outside diameter ... 64.5 mm (2.54 inch) (27) As required, use the following shims in order to obtain an end play of 0.03 to 0.08 mm (0.001 to 0.003 inch). All the shims must be located against the bearing cup of the rear transmission case. The 121-7398 Spacer must be in contact with the rear