2752673 EDGE AS Caterpillar parts
325D L, 329D, 329D L, 329E
Rating:
Alternative (cross code) number:
CA2752673
275-2673
2752673
CA2752673
275-2673
2752673
EXCAVATOR,
Number on catalog scheme:
1
For full view, you need register
Information:
Illustration 1 g01525061
Note: Lubricate all of the bores, shafts, and O-rings with the lubricant that is being sealed. (1) Heat the bearing cone to 120°C (248°F) for a maximum of 8 hours.Install the bearing cone.After the assembly has cooled, position the assembly squarely against the locating shoulder.The bearing cup may be frozen in order to aid installation.Note: Lubricate all of the bearings with SAE 30 oil prior to assembly. (2) Thickness of four new discs for the brake and thickness of three new plates for the brake ... 22.9 0.87 mm (0.900 0.034 inch)Note: Each side has four friction discs and three plates.Thickness of one new 170-8714 Friction Disc ... 4.00 0.12 mm (0.157 0.005 inch)Thickness of one new 3W-5159 Plate ... 2.30 0.13 mm (0.091 0.005 inch)Lubricate the discs and the plates with SAE 30 oil before assembly. (3) Rubber toric sealsAll the surfaces that are contacting the rubber toric seals must be clean and dry at assembly.Before assembly, apply a thin film of oil to the contacting surfaces of the metal seal rings.The seal rings must be assembled square with the bore and with the toric seal. The seal rings must not have bulges or twists.ReferenceRefer to Special Instruction, SEHS8364, "Assembly and Installation of Conventional Duo-Cone Seals" for installing the 9G-5343 Duo-Cone Seal Gp . (4) Apply 6V-5765 Sealant 1 mL (0.034 oz) to each location.Note: Clean all sealing surfaces prior to applying the sealant. (5) Tightening torque for 18 bolts ... 120 20 N m (89 15 lb ft) (6) Tightening torque for 58 bolts ... 300 40 N m (220 30 lb ft) (7) Tightening torque for 38 bolts ... 570 80 N m (420 60 lb ft) (8) Tightening for six plugs ... 105 10 N m (77 7 lb ft) (9) Tightening for eight bolts ... 570 80 N m (420 60 lb ft)Note: Apply 5P-3413 Pipe Sealant or 185-3992 Pipe Sealant to two plugs (10) . (10) Tightening for two plugs ... 75 N m (55 lb ft) (11) Tightening for six bolts ... 570 80 N m (420 60 lb ft)After you join the parts, tighten the bolts to the specified torque within 5 minutes. The pH of the sealing surface should not exceed 7.5.Procedure for Preloading the Sprocket Bearings
ReferenceDisassembly and Assembly, "Final Drive and Sprocket - Assemble"Tightening Sequence For The Sprocket Segments
ReferenceDisassembly and Assembly, "Sprocket Segment - Remove and Install"
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
2322923
EDGE
318C, 320C, 320D, 320D L, 320D LRR, 321C, 322B L, 322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330B L
318C, 320C, 320D, 320D L, 320D LRR, 321C, 322B L, 322C, 324D, 324D L, 325B L, 325C, 325D L, 329D L, 330B L
1748029
EDGE-CUTTING
318C, 320C, 320D, 320D L, 320D LRR, 321C, 322C, 324D, 324D L, 325C, 325D L, 330D L, 336D L
318C, 320C, 320D, 320D L, 320D LRR, 321C, 322C, 324D, 324D L, 325C, 325D L, 330D L, 336D L
2794101
EDGE AS
320C, 320D, 320D L, 320D LRR, 324D, 324D L, 324E L, 324E LN, 325B L, 325C, 325D L, 329D, 329D L, 329E L, 330D L, 336D L, 336E L
320C, 320D, 320D L, 320D LRR, 324D, 324D L, 324E L, 324E LN, 325B L, 325C, 325D L, 329D, 329D L, 329E L, 330D L, 336D L, 336E L
2794110
EDGE AS
322C, 324D, 324D L, 324E LN, 325B L, 325C, 325D L, 329D L, 329E LN, 330C L, 330D L, 336D L, 336E L
322C, 324D, 324D L, 324E LN, 325B L, 325C, 325D L, 329D L, 329E LN, 330C L, 330D L, 336D L, 336E L
2550475
EDGE AS
320D, 324D, 324D L, 324E, 329E
320D, 324D, 324D L, 324E, 329E
2902838
EDGE AS
324D, 324D L, 325D L, 329D, 329D L, 330D L, 336D
324D, 324D L, 325D L, 329D, 329D L, 330D L, 336D
3690632
EDGE AS
324D, 324D L, 329D L, 336D, 336D2
324D, 324D L, 329D L, 336D, 336D2
2752715
EDGE AS
325D L, 328D LCR, 329D, 329D L, 329E
325D L, 328D LCR, 329D, 329D L, 329E
2752715
EDGE AS
325D L, 328D LCR, 329D, 329D L, 329E
325D L, 328D LCR, 329D, 329D L, 329E
2748285
EDGE AS
345C, 345C L, 345D L, 345D L VG
345C, 345C L, 345D L, 345D L VG
2575364
EDGE AS
345C, 345C L, 345D L, 345D L VG
345C, 345C L, 345D L, 345D L VG
2731429
EDGE AS
345C, 345C L, 345D L, 345D L VG
345C, 345C L, 345D L, 345D L VG
2731430
EDGE AS
345C, 345C L, 345D L, 345D L VG
345C, 345C L, 345D L, 345D L VG
2575362
EDGE AS
345C, 345C L, 345D L, 345D L VG
345C, 345C L, 345D L, 345D L VG
3240059
EDGE AS
330D L, 336D L
330D L, 336D L
2794126
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
2794125
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
2794124
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
2794123
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
3110948
EDGE AS
330D L, 330D LN, 336D L, 336D LN, 336D2
330D L, 330D LN, 336D L, 336D LN, 336D2