2794093 EDGE AS Caterpillar parts
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E L, 320E LN, 320E LRR, 321C, 321D LCR, 322B L, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
Rating:
Alternative (cross code) number:
CA2794093
279-4093
2794093
CA2794093
279-4093
2794093
Weight: 339 pounds 153 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$15.89
19 Dec 2020
-: -
Kyocera SGS Precision Tools, 2794.093 ENDMILL 4FL BN TA, 0.0930 Cutting Diameter, 1.1160 Length of Cut, 1.3840, Shank Diameter, 2.5000 Overall Length, Carbide, TA Coated
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 2794093:
Information:
Illustration 1 g01159081This diagnostic code is associated with the solenoid valve for raising the right end of the blade. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal.The possible causes of this diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2161 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active the hydraulic control system will default to the "Auto Not Allowed" state.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J1-66 (wire K814-PK(Pink)) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-66 (K814-PK(Pink)) and the circuit that has a low resistance measurement.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Determine if the CID 2161 FMI 03 is active. Expected Result:The CID 2161 FMI 03 is active.Results:
YES - The CID 2161 FMI 03 is active. The problem has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Module - Replace".STOP
NO - The CID 2161 FMI 03 is not active. The problem does not exist at this time.Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOP
Cat SIS web machinery list:
Parts edge Caterpillar catalog:
311C, 311D LRR, 311F LRR, 312C L, 312D, 314C, 314D LCR, 315C, 315D L, 320C, 322C, 325B L, D6E, D6E SR, D6G, D6G SR, D6G2 XL, D6T XL
315C, 320C, 322C, 325B L, 924G, 924GZ, 924H, 924K, 928HZ, 930G, 930K, 938K
321C, 321D LCR, D5H XL, D5R LGP, D6H, D6M, D6N, D6N LGP, D6R, D6R II, D6T XL
321C, 321D LCR, 930K, D5H
320C, 630B, 631B, 631D, 631G, 637, 637B, 637D, 637E, 637G, 9A
320C
4396522
EDGE
320E LN
320E LN
4396520
EDGE AS
320E LN
320E LN
4393318
EDGE AS
320E LN
320E LN
2794123
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
2794124
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
2794125
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
2794092
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322B L, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322B L, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
2794091
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
2794090
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LN, 320E LRR, 321C, 321D LCR, 322C, 323D L, 323E L, 324D, 324D L, 324E L, 325D L, 329D, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LN, 320E LRR, 321C, 321D LCR, 322C, 323D L, 323E L, 324D, 324D L, 324E L, 325D L, 329D, 329E L
2392650
EDGE AS
318C, 320C
318C, 320C
2392642
EDGE AS
318C, 320C
318C, 320C
2392545
EDGE AS
318C, 320C
318C, 320C
1515515
EDGE AS
315C
315C
1748029
EDGE-CUTTING
318C, 320C, 320D, 320D L, 320D LRR, 321C, 322C, 324D, 324D L, 325C, 325D L, 330D L, 336D L
318C, 320C, 320D, 320D L, 320D LRR, 321C, 322C, 324D, 324D L, 325C, 325D L, 330D L, 336D L
3477467
EDGE AS
318C, 320E LN, 320E LRR, 323E L, M318D, M318D MH, M322C, M322D, M322D MH
318C, 320E LN, 320E LRR, 323E L, M318D, M318D MH, M322C, M322D, M322D MH
2794096
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L
2794095
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325B L, 325C, 325D L, 329D L, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325B L, 325C, 325D L, 329D L, 329E L
2794094
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325D, 325D L, 329D L, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325D, 325D L, 329D L, 329E L