2794094 EDGE AS Caterpillar parts
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325D, 325D L, 329D L, 329E L
Rating:
Alternative (cross code) number:
CA2794094
279-4094
2794094
CA2794094
279-4094
2794094
Weight: 375 pounds 170 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
Compatible equipment models: 2794094:
Number on catalog scheme:
1
For full view, you need register
Information:
Illustration 1 g01159081This diagnostic code is associated with the solenoid valve for lowering the left end of the blade. The FMI 06 means that the ECM has determined that there is a short to ground in the solenoid circuit.The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2162 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active the hydraulic control system will default to the "Service Mode" state.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:CID 2162 FMI 06 changes to CID 2162 FMI 05 when the solenoid is disconnected.Results:
YES - CID 2162 FMI 06 changes to CID 2162 FMI 05 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.STOP
NO - CID 2162 FMI 06 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J1-65 (wire K812-OR(Orange)) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-65 (wire K812-OR(Orange)) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 2162 FMI 06. Expected Result:The CID 2162 FMI 06 is active.Results:
YES - The CID 2162 FMI 06 is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Module - Replace". STOP
NO - The CID 2162 FMI 06 is
Cat SIS web machinery list:
Parts edge Caterpillar catalog:
311C, 311D LRR, 311F LRR, 312C L, 312D, 314C, 314D LCR, 315C, 315D L, 320C, 322C, 325B L, D6E, D6E SR, D6G, D6G SR, D6G2 XL, D6T XL
315C, 320C, 322C, 325B L, 924G, 924GZ, 924H, 924K, 928HZ, 930G, 930K, 938K
321C, 321D LCR, D5H XL, D5R LGP, D6H, D6M, D6N, D6N LGP, D6R, D6R II, D6T XL
321C, 321D LCR, 930K, D5H
320C, 630B, 631B, 631D, 631G, 637, 637B, 637D, 637E, 637G, 9A
320C
3780383
EDGE AS
320E L, 320E LRR
320E L, 320E LRR
3780384
EDGE AS
320E L, 320E LRR
320E L, 320E LRR
3780385
EDGE AS
320E L, 320E LRR
320E L, 320E LRR
2794123
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
2794124
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
2794125
EDGE AS
329D L, 330D L, 336D L, 336E L
329D L, 330D L, 336D L, 336E L
2794093
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E L, 320E LN, 320E LRR, 321C, 321D LCR, 322B L, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E L, 320E LN, 320E LRR, 321C, 321D LCR, 322B L, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
2794092
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322B L, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322B L, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
2794091
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325D L, 329D L, 329E L
2794090
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LN, 320E LRR, 321C, 321D LCR, 322C, 323D L, 323E L, 324D, 324D L, 324E L, 325D L, 329D, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LN, 320E LRR, 321C, 321D LCR, 322C, 323D L, 323E L, 324D, 324D L, 324E L, 325D L, 329D, 329E L
2392650
EDGE AS
318C, 320C
318C, 320C
2392642
EDGE AS
318C, 320C
318C, 320C
2126142
EDGE
303.5
303.5
1515515
EDGE AS
315C
315C
1748029
EDGE-CUTTING
318C, 320C, 320D, 320D L, 320D LRR, 321C, 322C, 324D, 324D L, 325C, 325D L, 330D L, 336D L
318C, 320C, 320D, 320D L, 320D LRR, 321C, 322C, 324D, 324D L, 325C, 325D L, 330D L, 336D L
3477467
EDGE AS
318C, 320E LN, 320E LRR, 323E L, M318D, M318D MH, M322C, M322D, M322D MH
318C, 320E LN, 320E LRR, 323E L, M318D, M318D MH, M322C, M322D, M322D MH
2794096
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L
2794095
EDGE AS
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325B L, 325C, 325D L, 329D L, 329E L
318C, 320C, 320D, 320D L, 320D LRR, 320D RR, 320E L, 320E LRR, 321C, 321D LCR, 322C, 323D L, 324D, 324D L, 324E L, 325B L, 325C, 325D L, 329D L, 329E L