3692473 EDGE-CUTTING Caterpillar parts
336D L, 336D2, 336D2 L, 349D L
Rating:
Alternative (cross code) number:
CA3692473
369-2473
3692473
CA3692473
369-2473
3692473
Weight: 48 pounds 22 kg.
EXCAVATOR,
Number on catalog scheme:
5E
For full view, you need register
Information:
open is a failure of an electrical circuit that results in no flow of electrical current. An open circuit is caused by failed electrical wires or a poor connection of electrical connectors. If an electrical wire or a connection is broken, the flow of electrical current through the circuit is interrupted. A normally closed circuit will have less than 5 ohms of resistance. The following procedure explains the test for an open circuit:ReferenceFor a complete electrical schematic, refer to the Electrical Schematic for the machine that is being serviced.TEST FOR AN OPEN CIRCUIT.
Identify the connectors and the wire numbers of the suspect circuits. Use the Electrical Schematic of the machine to identify the circuits.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the component and the Electronic Control Module (ECM) from the wiring harness.
At one of the disconnected harness connections, place a jumper wire from the contact of the suspect wire to frame ground.
At the other connector of the machine harness, use multimeter probes to measure resistance between the suspect wire contact and frame ground.Expected Result: The resistance is less than 5 ohms. OK - The resistance is less than 5 ohms. The harness circuit is correct.Stop. NOT OK - The resistance is greater than 5.0 ohms. There is an open in the machine harness.Repair: Repair the machine harness or replace the machine harness.Stop.
Identify the connectors and the wire numbers of the suspect circuits. Use the Electrical Schematic of the machine to identify the circuits.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the component and the Electronic Control Module (ECM) from the wiring harness.
At one of the disconnected harness connections, place a jumper wire from the contact of the suspect wire to frame ground.
At the other connector of the machine harness, use multimeter probes to measure resistance between the suspect wire contact and frame ground.Expected Result: The resistance is less than 5 ohms. OK - The resistance is less than 5 ohms. The harness circuit is correct.Stop. NOT OK - The resistance is greater than 5.0 ohms. There is an open in the machine harness.Repair: Repair the machine harness or replace the machine harness.Stop.
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
3668920
EDGE AS
336D2, 340D L, 340D2 L, 345D, 345D L, 349D, 349D L, 349E L
336D2, 340D L, 340D2 L, 345D, 345D L, 349D, 349D L, 349E L
3166091
EDGE AS
336D L, 345D L, 349E L, 349E L VG
336D L, 345D L, 349E L, 349E L VG
3393753
EDGE AS
336D, 336D L, 336D2, 336D2 L, 336E LN, 340D L, 340D2 L, 345D L, 349E L VG
336D, 336D L, 336D2, 336D2 L, 336E LN, 340D L, 340D2 L, 345D L, 349E L VG
3690873
EDGE AS
336D L, 336D2, 336D2 L, 349D L
336D L, 336D2, 336D2 L, 349D L
3692474
EDGE-CUTTING
336D L, 336D2, 336D2 L, 349D L
336D L, 336D2, 336D2 L, 349D L
3692475
EDGE-CUTTING
336D L, 336D2, 336D2 L, 349D L
336D L, 336D2, 336D2 L, 349D L
3603931
EDGE AS
336D, 336D L, 336D2, 336E LN, 349E L VG
336D, 336D L, 336D2, 336E LN, 349E L VG
3687996
EDGE AS
336D L, 336D2, 336D2 L, 349D L
336D L, 336D2, 336D2 L, 349D L
3649400
EDGE AS
336D, 336D2
336D, 336D2
3590867
EDGE AS
336D L, 336D2, 336D2 L, 336E LN, 349D L, 349E L VG
336D L, 336D2, 336D2 L, 336E LN, 349D L, 349E L VG
3699903
EDGE AS
336D L, 336D2, 336D2 L
336D L, 336D2, 336D2 L
3573603
EDGE AS
349D L, 349E L VG
349D L, 349E L VG
3690873
EDGE AS
336D L, 336D2, 336D2 L, 349D L
336D L, 336D2, 336D2 L, 349D L
3793032
EDGE AS
374D L
374D L
3531759
EDGE AS
374D L, 374F L
374D L, 374F L
3531756
EDGE AS
374D L, 374F L
374D L, 374F L
3531753
EDGE AS
374D L, 374F L
374D L, 374F L
3531747
EDGE AS
374D L, 374F L
374D L, 374F L
3590867
EDGE AS
336D L, 336D2, 336D2 L, 336E LN, 349D L, 349E L VG
336D L, 336D2, 336D2 L, 336E LN, 349D L, 349E L VG
3649400
EDGE AS
336D, 336D2
336D, 336D2
3687996
EDGE AS
336D L, 336D2, 336D2 L, 349D L
336D L, 336D2, 336D2 L, 349D L
3603931
EDGE AS
336D, 336D L, 336D2, 336E LN, 349E L VG
336D, 336D L, 336D2, 336E LN, 349E L VG
3692475
EDGE-CUTTING
336D L, 336D2, 336D2 L, 349D L
336D L, 336D2, 336D2 L, 349D L
3692474
EDGE-CUTTING
336D L, 336D2, 336D2 L, 349D L
336D L, 336D2, 336D2 L, 349D L