4775565 EDGE GP-CUTTING Caterpillar parts
Rating:
Alternative (cross code) number:
CA4775565
477-5565
4775565
CA4775565
477-5565
4775565
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Oil Filter LJ657 11214514 P550425 477556-5 4775565 21707132 Compatible for EC300B EC300CL EC300BLC EC380BLC EC460BLC EC380DL EC480DL EC700BLC EC750DL Compatible for Temporary worker E6330E E6360E
Wieoncke 【NOTE】: If you cannot find the part number you need, please consult us. We will provide quotation information as soon as possible. || 【Part Name】:Oil Filter || 【Part Number】:CJ-625X MB-JX634 LJ657 11214514 P550425 477556-5 4775565 21707132 || 【Application】: Compatible for EC300B EC300CL EC300BLC EC380BLC EC460BLC EC380DL EC480DL EC700BLC EC750DL Compatible for Temporary worker E6330E E6360E E6360F E6400E E6460F E6500F E6550F || 【 Important 】: To avoid unnecessary returns, please purchase based on the old part number. If you are unsure of the part number, please send us a picture of the engine nameplate and we will match the correct part number for you as soon as possible!
Wieoncke 【NOTE】: If you cannot find the part number you need, please consult us. We will provide quotation information as soon as possible. || 【Part Name】:Oil Filter || 【Part Number】:CJ-625X MB-JX634 LJ657 11214514 P550425 477556-5 4775565 21707132 || 【Application】: Compatible for EC300B EC300CL EC300BLC EC380BLC EC460BLC EC380DL EC480DL EC700BLC EC750DL Compatible for Temporary worker E6330E E6360E E6360F E6400E E6460F E6500F E6550F || 【 Important 】: To avoid unnecessary returns, please purchase based on the old part number. If you are unsure of the part number, please send us a picture of the engine nameplate and we will match the correct part number for you as soon as possible!
Oil Filter P550425 LF3654 477556-5 4775565 21707132 ST10502 OV-J2058 CJ-625X Compatible for Compatible for EC300B EC300CL EC300BLC EC380BLC EC460BLC EC380DL EC480DL EC700BLC EC750DL
Wieoncke 【NOTE】: If you cannot find the part number you need, please consult us. We will provide quotation information as soon as possible. || 【Part Name】:Oil Filter || 【Part Number】:JM-2058 P550425 LF3654 477556-5 4775565 21707132 ST10502 OV-J2058 CJ-625X || 【Application】:Compatible for Temporary worker 360F E6330E E6360E E6360F E6400E E6460F E6500F E6550F EC300B EC360BLC EC350BLC EC380BLC EC460BLC EC380DL EC480DL EC700BLC EC750DL Compatible for EC300B EC300CL EC300BLC EC380BLC EC460BLC EC380DL EC480DL EC700BLC EC750DL Compatible for dragon-work E6330E E6360E E6360F E6400E E6460F E6500F E6550F || 【 Important 】: To avoid unnecessary returns, please purchase based on the old part number. If you are unsure of the part number, please send us a picture of the engine nameplate and we will match the correct part number for you as soon as possible!
Wieoncke 【NOTE】: If you cannot find the part number you need, please consult us. We will provide quotation information as soon as possible. || 【Part Name】:Oil Filter || 【Part Number】:JM-2058 P550425 LF3654 477556-5 4775565 21707132 ST10502 OV-J2058 CJ-625X || 【Application】:Compatible for Temporary worker 360F E6330E E6360E E6360F E6400E E6460F E6500F E6550F EC300B EC360BLC EC350BLC EC380BLC EC460BLC EC380DL EC480DL EC700BLC EC750DL Compatible for EC300B EC300CL EC300BLC EC380BLC EC460BLC EC380DL EC480DL EC700BLC EC750DL Compatible for dragon-work E6330E E6360E E6360F E6400E E6460F E6500F E6550F || 【 Important 】: To avoid unnecessary returns, please purchase based on the old part number. If you are unsure of the part number, please send us a picture of the engine nameplate and we will match the correct part number for you as soon as possible!
1 Pcs 477556-5 21707132 Oil Filter Element LF3654 LF3410 P55-0425 Compatible with Volvo Car
Generic 【PACKAGE INCLUDES】1*Filter. || 【FEATURES】Designed to filter out various impurities in the engine fuel system. It reduces mechanical wear, ensures stable engine operation and improves reliability. || 【INSTALLATION INSTRUCTIONS】Please recycle the used filter.Don't reuse.After installing a new filter, prime and start the engine and wait for a few minutes, then check for leakage. || 【Premium material】The filter is made from good-quality aluminum and rubber, which is durable, stable in performance, and not easy to break or deform. || 【NOTE】Different part numbers represent different parts, please check your manual for specific parameters.
Generic 【PACKAGE INCLUDES】1*Filter. || 【FEATURES】Designed to filter out various impurities in the engine fuel system. It reduces mechanical wear, ensures stable engine operation and improves reliability. || 【INSTALLATION INSTRUCTIONS】Please recycle the used filter.Don't reuse.After installing a new filter, prime and start the engine and wait for a few minutes, then check for leakage. || 【Premium material】The filter is made from good-quality aluminum and rubber, which is durable, stable in performance, and not easy to break or deform. || 【NOTE】Different part numbers represent different parts, please check your manual for specific parameters.
Number on catalog scheme:
For full view, you need register
Information:
the negative test lead to wire "110C-GY" on the voltage/frequency converter in order to verify that 24 DCV is present.
Move the positive test lead to wire "111-RD" on the voltage/frequency converter.
The negative test lead remains connected to wire "110C-GY". Verify that the input voltage for the voltage/frequency converter is 5 1 mV. This voltage matches the output voltage for the current transducer. The voltage is 5 1 mV for both readings.
Set the Digital Multimeter on the scale for frequency ("Hz").
Connect the positive test lead to wire "112-PK" on the voltage/frequency converter.
The negative test lead remains connected to wire "110C-GY".
Read the output frequency of the voltage/frequency converter.Expected Result:The frequency is 60 5 Hz. Results:
YES - The frequency is 60 5 Hz. The frequency is correct. Proceed to Test Step 21.
NO - The frequency is not 60 5 Hz. The voltage/frequency converter has failed. Repair: Replace the voltage/frequency converter. STOPTest Step 21. DROP SOLID STATE RELAY TESTNote: See Electrical Schematic, RENR3125.
Set the Digital Multimeter on the "AUTO" setting or set the multimeter on the "40 DCV" scale.
Connect the positive test lead to terminal "101C".
Connect the negative test lead to terminal "102D".
Start the engine and run the engine at high idle.
Verify that the magnet/grapple switch is in the magnet position.
Depress the lift switch in the right-hand joystick.
After 3 seconds, depress the drop switch. The drop switch is located in the left-hand controller. Observe the multimeter. Expected Result:The multimeter reads approximately 28 DCV when the terminal "101C" is positive during the lift cycle. The multimeter reads approximately, negative 28 DCV when the terminal "101C" is negative during the drop cycle. Results:
YES - The multimeter reads approximately 28 DCV when the terminal "101C" is positive during the lift cycle. The multimeter reads approximately, negative 28 DCV when the terminal "101C" is negative during the drop cycle. The drop solid-state relays are functioning properly. Proceed to Test Step 24.
NO - The multimeter reads approximately 28 DCV when the terminal "101C" is positive during the lift cycle. The multimeter does NOT read a negative voltage during the drop cycle. The solid-state relay ("SSR172") may have failed. Also, The solid-state relay ("SSR173") may have failed. Proceed to Test Step 22 in order to determine the relay that has failed.Test Step 22. TEST FOR THE DROP SOLID STATE RELAY (SSR172).Note: Refer to the electrical system schematic Schematic, RENR3125.
Connect the positive test lead to terminal "102D".
Connect the negative test lead to terminal "102C".
Press the lift switch in the right-hand controller.
Wait for 3 seconds. Then press the drop switch in the left-hand controller. Observe the voltmeter while you perform this Test Step. Expected Result:The meter indicates zero DCV during lift. The meter indicates approximately 28 DCV with the positive terminal "102D" during the drop.Results:
YES - The meter indicates zero DCV during lift. The meter indicates approximately 28 DCV with the positive terminal "102D" during the drop. The relay is functioning properly. Proceed to Test Step 23.
NO - The meter indicates zero DCV during Lift
Move the positive test lead to wire "111-RD" on the voltage/frequency converter.
The negative test lead remains connected to wire "110C-GY". Verify that the input voltage for the voltage/frequency converter is 5 1 mV. This voltage matches the output voltage for the current transducer. The voltage is 5 1 mV for both readings.
Set the Digital Multimeter on the scale for frequency ("Hz").
Connect the positive test lead to wire "112-PK" on the voltage/frequency converter.
The negative test lead remains connected to wire "110C-GY".
Read the output frequency of the voltage/frequency converter.Expected Result:The frequency is 60 5 Hz. Results:
YES - The frequency is 60 5 Hz. The frequency is correct. Proceed to Test Step 21.
NO - The frequency is not 60 5 Hz. The voltage/frequency converter has failed. Repair: Replace the voltage/frequency converter. STOPTest Step 21. DROP SOLID STATE RELAY TESTNote: See Electrical Schematic, RENR3125.
Set the Digital Multimeter on the "AUTO" setting or set the multimeter on the "40 DCV" scale.
Connect the positive test lead to terminal "101C".
Connect the negative test lead to terminal "102D".
Start the engine and run the engine at high idle.
Verify that the magnet/grapple switch is in the magnet position.
Depress the lift switch in the right-hand joystick.
After 3 seconds, depress the drop switch. The drop switch is located in the left-hand controller. Observe the multimeter. Expected Result:The multimeter reads approximately 28 DCV when the terminal "101C" is positive during the lift cycle. The multimeter reads approximately, negative 28 DCV when the terminal "101C" is negative during the drop cycle. Results:
YES - The multimeter reads approximately 28 DCV when the terminal "101C" is positive during the lift cycle. The multimeter reads approximately, negative 28 DCV when the terminal "101C" is negative during the drop cycle. The drop solid-state relays are functioning properly. Proceed to Test Step 24.
NO - The multimeter reads approximately 28 DCV when the terminal "101C" is positive during the lift cycle. The multimeter does NOT read a negative voltage during the drop cycle. The solid-state relay ("SSR172") may have failed. Also, The solid-state relay ("SSR173") may have failed. Proceed to Test Step 22 in order to determine the relay that has failed.Test Step 22. TEST FOR THE DROP SOLID STATE RELAY (SSR172).Note: Refer to the electrical system schematic Schematic, RENR3125.
Connect the positive test lead to terminal "102D".
Connect the negative test lead to terminal "102C".
Press the lift switch in the right-hand controller.
Wait for 3 seconds. Then press the drop switch in the left-hand controller. Observe the voltmeter while you perform this Test Step. Expected Result:The meter indicates zero DCV during lift. The meter indicates approximately 28 DCV with the positive terminal "102D" during the drop.Results:
YES - The meter indicates zero DCV during lift. The meter indicates approximately 28 DCV with the positive terminal "102D" during the drop. The relay is functioning properly. Proceed to Test Step 23.
NO - The meter indicates zero DCV during Lift
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
4775564
EDGE GP-CUTTING
Caterpillar
Caterpillar
4709332
EDGE-BASE
Caterpillar
Caterpillar
4709331
EDGE-BASE
Caterpillar
Caterpillar
4709330
EDGE-BASE
Caterpillar
Caterpillar
4709329
EDGE-BASE
Caterpillar
Caterpillar
4709328
EDGE-BASE
Caterpillar
Caterpillar
4814691
EDGE GP-CUTTING
Caterpillar
Caterpillar
4814671
EDGE GP-CUTTING
Caterpillar
Caterpillar
4814664
EDGE GP-CUTTING
Caterpillar
Caterpillar
4814663
EDGE GP-CUTTING
Caterpillar
Caterpillar
4775567
EDGE GP-CUTTING
Caterpillar
Caterpillar
4775566
EDGE GP-CUTTING
Caterpillar
Caterpillar