AVSPARE.COM
parts catalog

EDGE-CUTTING 4T3006 - Caterpillar


4T3006 EDGE-CUTTING Caterpillar parts D4E SR
Rating:
24
Alternative (cross code) number:
CA4T3006
4T-3006
4T3006
Caterpillar 4T3006 EDGE-CUTTING
Weight: 49 pounds 22 kg.
Information:
ABRASION RESISTANT MATERIAL 
BOLT HOLE SIZE  18  mm
CHAMFER  EDGE 
HOLE PATTERN  CENTERLINE 
HOLE SPACING  152.4  mm
LENGTH  807.6  mm
NUMBER OF HOLES 
THICKNESS  19  mm
TUNGSTEN CARBIDE 
WIDTH  203.2  mm

Buy EDGE-CUTTING 4T3006 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$104.82

09 Jun 2025

Amazon.com
CTP 4T3006 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each
$99.10

16 Sep 2024

Amazon.com
CTP 4T3006 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each
$94.85
 

10 May 2024

Amazon.com
CTP 4T3006 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each
Number on catalog scheme: 2
  For full view, you need register

Compatible equipment models: 4T3006:

TRACK-TYPE TRACTOR  D4E SR   Caterpillar

Information:


Clean the cooling system and flush the cooling system before the recommended maintenance interval if the following conditions exist:
The engine overheats frequently.
Foaming is observed.
The oil has entered the cooling system and the coolant is contaminated.
The fuel has entered the cooling system and the coolant is contaminated.Note: When the cooling system is cleaned, only clean water is needed when the ELC is drained and replaced.Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained.Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove the cooling system drain plugs.Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Dealer Service Tool Group:InsideUSA: 1-800-542-TOOLInside Illinois: 1-800-541-TOOLCanada: 1-800-523-TOOLInternational, 1-309-578-7372Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with clean water. Install the cooling system filler cap.
Start and run the engine at low idle until the temperature reaches 49 to 66 °C (120 to 150 °F).
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual, SENR3130, "Torque Specifications" for more information on the proper torques.

Caterpillar parts catalog:

Caterpillar parts catalog
D4E SR Track-Type Tractor Direct Drive 2DJ01400-UP (MACHINE) POWERED BY 3304 Engine


Parts edge Caterpillar catalog:

8J1490 EDGE-CUTTING
4A, 4S, 930, D4E, D4E SR
8J1489 EDGE-CUTTING
4A, 4S, 930, D4E, D4E SR
8J1489 EDGE-CUTTING
4A, 4S, 930, D4E, D4E SR
8J1490 EDGE-CUTTING
4A, 4S, 930, D4E, D4E SR
4T8084 EDGE-CUTTING
963, 963B, 963C, 963D
6W2980 EDGE-CUTTING
963, 963B, 963C, 963D
5G7610 EDGE-WEAR
963, 963B, 963C
8Y6263 EDGE-CUTTING
950H, 962H, 963B, 963C, 963D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.