4T3012 EDGE-CUTTING Caterpillar parts
815B, 815F, 815F II
Rating:
Alternative (cross code) number:
CA4T3012
4T-3012
4T3012
CA4T3012
4T-3012
4T3012
Weight: 93 pounds 42 kg.
Information:
ABRASION RESISTANT MATERIAL
N
BOLT HOLE SIZE
21
mm
CHAMFER
EDGE
HOLE PATTERN
CENTERLINE
HOLE SPACING
152.4
mm
LENGTH
1495.6
mm
NUMBER OF HOLES
10
THICKNESS
19
mm
TUNGSTEN CARBIDE
N
WIDTH
203.2
mm
SOIL COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 4T3012 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each
CTP For Ground Engaging Tools || Longer tips || Sold in each
CTP 4T3012 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each
CTP For Ground Engaging Tools || Longer tips || Sold in each
Number on catalog scheme:
13
For full view, you need register
4T3012
Images:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1 Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01342059
Remove isolating frame from the cylinder block. Follow steps 1.a through 1.c in order to remove the isolating frame from the cylinder block.
Support the isolating frame (3). Use Tooling (A) to remove the torx screws (2) and (4).
Remove the isolating frame (3) from the cylinder block.
Remove the joint (1). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1
B - Guide Stud
(M8 by 100 mm) 4
C - Loctite 5900 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 2 g01342186
Typical example
Install Tooling (B) to Positions (X) in the cylinder block.
Install the isolating frame to the cylinder block. Follow Steps 2.a through 2.f in order to install the isolating frame.
Ensure that the joint face of the cylinder block is clean and free from damage.
Ensure that the isolating frame is clean and free from damage. If necessary, replace the isolating frame.
Illustration 3 g01342058
Tooling (B) is not shown for clarity.
Apply a bead of Tooling (C) to Positions (Y).
Illustration 4 g01342059
Position a new joint (1) onto the isolating frame (3).
Align the isolating frame (3) with Tooling (B). Install the isolating frame to the cylinder block.
Use Tooling (A) to install the two torx screws (2) and the four torx screws (4) to the isolating frame. Tighten the torx screws (2) to a torque of 22 N m (16 lb ft). Tighten the torx screws (4) to a torque of 22 N m (16 lb ft). End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1 Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01342059
Remove isolating frame from the cylinder block. Follow steps 1.a through 1.c in order to remove the isolating frame from the cylinder block.
Support the isolating frame (3). Use Tooling (A) to remove the torx screws (2) and (4).
Remove the isolating frame (3) from the cylinder block.
Remove the joint (1). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1
B - Guide Stud
(M8 by 100 mm) 4
C - Loctite 5900 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 2 g01342186
Typical example
Install Tooling (B) to Positions (X) in the cylinder block.
Install the isolating frame to the cylinder block. Follow Steps 2.a through 2.f in order to install the isolating frame.
Ensure that the joint face of the cylinder block is clean and free from damage.
Ensure that the isolating frame is clean and free from damage. If necessary, replace the isolating frame.
Illustration 3 g01342058
Tooling (B) is not shown for clarity.
Apply a bead of Tooling (C) to Positions (Y).
Illustration 4 g01342059
Position a new joint (1) onto the isolating frame (3).
Align the isolating frame (3) with Tooling (B). Install the isolating frame to the cylinder block.
Use Tooling (A) to install the two torx screws (2) and the four torx screws (4) to the isolating frame. Tighten the torx screws (2) to a torque of 22 N m (16 lb ft). Tighten the torx screws (4) to a torque of 22 N m (16 lb ft). End By:
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
D11N, D11R, D11T
D11N, D11R, D11T
9W2424
EDGE-CUTTING
D11N, D11R
D11N, D11R
D11N, D11R
1457846
EDGE-CUTTING
D7R, D7R II
D7R, D7R II
854G, 854K, D10N, D10R, D10T, D10T2
826C, 826G, 826G II, 826H, 826K, 834B, D7E, D7E LGP
5J6807
EDGE-CUTTING
824S, 826C, 834B
824S, 826C, 834B
1233754
EDGE-CUTTING
834B
834B
1093146
EDGE-CUTTING
834B
834B