4T6238 EDGE-CUTTING Caterpillar parts
825C, 825G, 825G II, 825H, 825K
Rating:
Alternative (cross code) number:
CA4T6238
4T-6238
4T6238
CA4T6238
4T-6238
4T6238
Weight: 123 pounds 55 kg.
Information:
ABRASION RESISTANT MATERIAL
N
BOLT HOLE SIZE
28
mm
CHAMFER
EDGE
HOLE PATTERN
CENTERLINE
HOLE SPACING
152.4
mm
LENGTH
1199.8
mm
NUMBER OF HOLES
8
THICKNESS
25
mm
TUNGSTEN CARBIDE
N
WIDTH
254
mm
SOIL COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$297.06
25 Sep 2021
Amazon.com
CTP 4T6238 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each
CTP For Ground Engaging Tools || Longer tips || Sold in each
$196.35
12 Sep 2021
123.2824[55.48] Pounds
US: IronDT
Caterpillar CUTTING EDGE (4T6238) New Aftermarket By CTP
CTP
CTP
$189.06
20 Nov 2020
124.0[55.80] Pounds
-: -
4T6238 Edge-Cutting Fits Caterpillar 825G 825G II 825H
4T6238 Edge-cutting
4T6238 Edge-cutting
For full view, you need register
4T6238
Images:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
E 1U-7598 Seal Installer Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Replacement rear seals are supplied with a wear sleeve. This wear sleeve must be installed with the rear seal. New engines from the factory do not have a wear sleeve. Do not install the rear seal if any of the following conditions exist:
The crankshaft rear seal has been separated from the wear sleeve.
The rear seal group appears to be damaged.
The crankshaft rear seal has been lubricated. The seal is designed to be installed dry.
Ensure that the rear of the crankshaft is thoroughly clean and dry prior to the installation of the crankshaft rear seal.
Illustration 1 g01026625
Typical example
Use Tooling (E) to install crankshaft rear seal (1). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
E 1U-7598 Seal Installer Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Replacement rear seals are supplied with a wear sleeve. This wear sleeve must be installed with the rear seal. New engines from the factory do not have a wear sleeve. Do not install the rear seal if any of the following conditions exist:
The crankshaft rear seal has been separated from the wear sleeve.
The rear seal group appears to be damaged.
The crankshaft rear seal has been lubricated. The seal is designed to be installed dry.
Ensure that the rear of the crankshaft is thoroughly clean and dry prior to the installation of the crankshaft rear seal.
Illustration 1 g01026625
Typical example
Use Tooling (E) to install crankshaft rear seal (1). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove and Install".
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
1376611
EDGE GP-BIT & CUTTING
825G, 825G II, 825H, 825K
825G, 825G II, 825H, 825K
825G, 826H, D7E, D7E LGP
825G, 825G II, 825H, 825K
824G, 824G II, 824H, 824K
814F, 814F II, 816B, 816F, 816F II, D7G, D7G2
1130322
EDGE-CUTTING
834G, D9R
834G, D9R
D9N, D9R
834G, 834H, 834K, D9N, D9R
1359661
EDGE-CUTTING
834B
834B
1359665
EDGE-CUTTING
834B
834B
1359662
EDGE-CUTTING
834B
834B
4T8798
EDGE-CUTTING
834B
834B
8J3165
EDGE GP-BIT & CUTTING
826G, 826G II, 826H, 826K
826G, 826G II, 826H, 826K
825G, 825G II, 825H, 825K