EDGE-CUTTING 4T6386 - Caterpillar

4T6386 EDGE-CUTTING Caterpillar parts 834G, 834H, 834K, 844, 844H, 844K

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4T6386
4T-6386
4T6386

Weight: 158 pounds 71 kg.

Information:

ABRASION RESISTANT MATERIAL N

BOLT HOLE SIZE 28 mm

CHAMFER EDGE

HOLE PATTERN CENTERLINE

HOLE SPACING 152.4 mm

LENGTH 1039.4 mm

NUMBER OF HOLES 7

THICKNESS 28.5 mm

TUNGSTEN CARBIDE N

WIDTH 330 mm

Buy EDGE-CUTTING 4T6386 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL DOZER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

4T6386 Edge-Cutting (New AFTERMARKET) - G&T Engine Parts

$495.94

15 Jul 2025

US: QUALITY PARTS

4T6386 Edge-Cutting (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 173.8 lbs || Dimensions: 10-14.33-44.99 in || Items are sold by part number only. Picture is for illustration purposes and the part or parts may be different in color or quantity. || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.

CTP 4T6386 Ground Engaging Tools Cutting Edge

$423.70

11 Jul 2025

Amazon.com

CTP 4T6386 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each

$432.44

13 May 2025

Amazon.com

CTP 4T6386 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each

Show more prices Caterpillar parts

This part in 1 request: Show. This information for suppliers only!

#1330237 4T6386

2024-04-27

Number on catalog scheme: 21

Caterpillar 4T6386 Parts scheme EDGE-CUTTING

For full view, you need register

4T6386 Images:

Compatible equipment models: 4T6386:

WHEEL DOZER 834G 834H 834K 844 844H 844K Caterpillar

Information:

Illustration 1 g00482547
Magnetic switches on subpanel(Two switches that are shown are for the system with two starting motors.)The starting motor magnetic switch (SMMS) for the 24 VDC systems is mounted on the subpanel within the control panel. Two switches are used in a system with two starting motors. One switch is used for each starting motor.Test Procedure
Disconnect the wire at terminal 25 of the "Status Control Module (SCM)". Measure the resistance between the wire that was removed from terminal 25 and the −Battery at the SCM.
The resistance should measure 26 to 33 Ohms for the systems with one starting motor.
The resistance should measure 13 to 17 Ohms for the systems with two starting motors.If resistance is not correct, replace the faulty magnetic switch.
If the resistance is correct, disconnect the cable that is going from the pinion solenoid to the starting motor. Do this procedure on both starting motors of a system with two starting motors.
Connect a DC voltmeter. Connect the positive cable to the +Battery and the negative cable to terminal 3 of the magnetic switch. (If the second magnetic switch is tested in a system with two starting motors, connect the negative cable to terminal 3 of the second magnetic switch.)
Connect a jumper wire to the wire that was removed from terminal 25 of the SCM. Disconnect this wire immediately after the voltage is measured. Do not leave the wire on more than ten seconds. The correct measurement changes from approximately 24 VDC to approximately 2 VDC.If voltage is greater than 2 VDC, replace the magnetic switch. If the switch passes the requirements of Test Step 1 and 4, the switch is functioning correctly. Reconnect the wires and cables that were removed in this procedure.