4T9587 EDGE-CUTTING Caterpillar parts
D8L
Rating:
Alternative (cross code) number:
CA4T9587
4T-9587
4T9587
CA4T9587
4T-9587
4T9587
Weight: 118 pounds 53 kg.
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$352.30
21 Feb 2022
US: Florida-Parts-Z
6Y5540 - Edge-Cutting 4t9587 for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Number on catalog scheme:
2
For full view, you need register
Compatible equipment models: 4T9587:
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-6363 Holding Fixture 1
B 9S-6343 Fixture Assembly 1
C 1P-1861 Retaining Ring Pliers 1
D FT-0745 Modified Pliers 1
E 8T-5096 Dial Indicator Gp 1
F 4L-7464 Silicone Grease -
G 5P-3931 Anti-Seize Compound - Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Ensure that all of the oil passages in the cartridge assembly are clean and free of dirt and foreign material.
Apply clean engine oil to all parts of the cartridge assembly.
Illustration 1 g01930813
Illustration 2 g01930815Note: Retaining rings (18), (19), (24), and (23) must be installed with the round edge of the retaining rings toward the bearing.
Use Tooling (D) in order to install retaining rings (18) and (19). Install retaining ring (18), bearing (14), and retaining ring (19) in the compressor end of the cartridge assembly.
Turn around the cartridge assembly and use Tooling (D) in order to install retaining rings (24) and (23).
Install retaining ring (24), bearing (22), sleeve (25), and retaining ring (23) in the turbine end of the cartridge assembly.
Illustration 3 g01930816
Place the seal ring into position in cartridge assembly (3). Check the end clearance for the seal ring. The maximum permissible end clearance is 0.23 mm (0.009 inch).
Illustration 4 g01930817
Apply Tooling (F) in groove (25) to one half or more of the depth of the groove all the way around turbine shaft (7).
Illustration 5 g01930818Note: Be careful not to break seal ring (8) during installation.
Install seal ring (8) on turbine shaft (7). Note: Ensure that seal ring (8) on turbine shaft (7) is correctly installed in the cartridge assembly.
Illustration 6 g01930819
Place shroud (6) in position on the cartridge assembly.
Install turbine shaft (7) in the cartridge assembly.
Illustration 7 g01930820
Install ring (15), bearing (20), sleeve (16), ring (21), and deflector (17) in the cartridge assembly.
Illustration 8 g01930821Note: Install seal rings (13) on sleeve (11). Ensure that the gaps in the seal rings are turned 180°.
Install seal rings (13) in the groove of sleeve (11).
Illustration 9 g01930822
Install O-ring seal (12) on insert (10).
Install sleeve (11) in insert (10).
Place insert (10) in position over the turbine shaft in the cartridge assembly.
Use Tooling (C) in order to install the retaining ring that holds the insert in the cartridge assembly.
Illustration 10
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-6363 Holding Fixture 1
B 9S-6343 Fixture Assembly 1
C 1P-1861 Retaining Ring Pliers 1
D FT-0745 Modified Pliers 1
E 8T-5096 Dial Indicator Gp 1
F 4L-7464 Silicone Grease -
G 5P-3931 Anti-Seize Compound - Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Ensure that all of the oil passages in the cartridge assembly are clean and free of dirt and foreign material.
Apply clean engine oil to all parts of the cartridge assembly.
Illustration 1 g01930813
Illustration 2 g01930815Note: Retaining rings (18), (19), (24), and (23) must be installed with the round edge of the retaining rings toward the bearing.
Use Tooling (D) in order to install retaining rings (18) and (19). Install retaining ring (18), bearing (14), and retaining ring (19) in the compressor end of the cartridge assembly.
Turn around the cartridge assembly and use Tooling (D) in order to install retaining rings (24) and (23).
Install retaining ring (24), bearing (22), sleeve (25), and retaining ring (23) in the turbine end of the cartridge assembly.
Illustration 3 g01930816
Place the seal ring into position in cartridge assembly (3). Check the end clearance for the seal ring. The maximum permissible end clearance is 0.23 mm (0.009 inch).
Illustration 4 g01930817
Apply Tooling (F) in groove (25) to one half or more of the depth of the groove all the way around turbine shaft (7).
Illustration 5 g01930818Note: Be careful not to break seal ring (8) during installation.
Install seal ring (8) on turbine shaft (7). Note: Ensure that seal ring (8) on turbine shaft (7) is correctly installed in the cartridge assembly.
Illustration 6 g01930819
Place shroud (6) in position on the cartridge assembly.
Install turbine shaft (7) in the cartridge assembly.
Illustration 7 g01930820
Install ring (15), bearing (20), sleeve (16), ring (21), and deflector (17) in the cartridge assembly.
Illustration 8 g01930821Note: Install seal rings (13) on sleeve (11). Ensure that the gaps in the seal rings are turned 180°.
Install seal rings (13) in the groove of sleeve (11).
Illustration 9 g01930822
Install O-ring seal (12) on insert (10).
Install sleeve (11) in insert (10).
Place insert (10) in position over the turbine shaft in the cartridge assembly.
Use Tooling (C) in order to install the retaining ring that holds the insert in the cartridge assembly.
Illustration 10
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
836G, 836H, D8L, D9R
824H, 824K, 826H, 826K, D8L, D9R, D9T
826H, 826K, D8L
D8L, D8R, D9T
980H, 980K, 980M, 988B, 988F, 990, 990 II, D8L
D8L
D8L, D9N
