AVSPARE.COM
parts catalog

EDGE GP-BIT & CUTTING 4Z9057 - Caterpillar



4Z9057 EDGE GP-BIT & CUTTING Caterpillar parts D8R, D8R II, D8T EDGE
Rating:
13
Alternative (cross code) number:
CA4Z9057
4Z-9057
4Z9057
Caterpillar 4Z9057 EDGE GP-BIT & CUTTING
Weight: 0.60 pounds 0 kg.

Buy EDGE GP-BIT & CUTTING 4Z9057 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 4Z9057:

TRACK-TYPE TRACTOR  D8R   D8R II   D8T   Caterpillar
Number on catalog scheme: 2
 
  For full view, you need register

Information:


Illustration 10 g01435442
Terminal locations at the P5 connector on the terminal box that are for the circuit of the coolant pressure sensor on vee engines (P5-11) Shield (P5-21) Sensor return (P5-29) Signal for the engine coolant pressure (P5-37) +8 Volt supply
Turn the engine control switch to the OFF/RESET position. Switch the 16 amp circuit breaker for the ECM OFF.
Remove the signal wire for the coolant pressure sensor from the P5 connector at the terminal box.
Use a multimeter that is capable of measuring both the duty cycle and the frequency. Connect the multimeter between the signal wire from the P5 connector and the sensor's return wire at the P5 connector.
Switch the 16 amp circuit breaker for the ECM ON. Turn the engine control switch to the STOP position.
Measure the duty cycle and the frequency of the sensor. Record the values.Expected Result:The frequency is between 400 and 600 Hz.The duty cycle is between 5 and 95 percent.The frequency and the duty cycle are approximately equal to the values that were recorded for the previous Test Step.Results:
OK - The frequency and the duty cycle of the signal are within the specifications. The signal that is developed by the sensor is present at the terminal box. The engine harness appears to be OK. There may be a problem with a connector or with the harness inside the terminal box. Proceed to Test Step 6.
Not OK - The frequency or the duty cycle of the signal are not within the specifications. The signal that is developed by the sensor is not present at the terminal box. The signal wire in the engine harness has a problem. There may be a problem with a connector.Repair: Repair the harness or the connector, when possible. Replace the harness, if necessary.STOPTest Step 6. Check the Sensor's Signal at the ECM
Illustration 11 g01435431
Harness side of the ECM P2 connector (P2-65) +8 Volt supply (P2-66) Sensor return (P2-68) Signal for the engine coolant pressure
Turn the engine control switch to the OFF/RESET position. Switch the 16 amp circuit breaker for the ECM OFF.
Remove the signal wire from terminal P2-68 at ECM connector P2. Use a multimeter that is capable of measuring both the duty cycle and the frequency. Connect the multimeter between the signal wire from the P2 connector and the sensor's return wire at terminal P2-66.
Switch the 16 amp circuit breaker for the ECM ON. Turn the engine control switch to the STOP position.
Measure the frequency and the duty cycle of the signal.Expected Result:The frequency is between 400 and 600 Hz.The duty cycle is between 5 and 95 percent.The frequency and the duty cycle are approximately equal to the values that were previously recorded.Results:
OK - The frequency and the duty cycle of the signal are within the specifications. The signal that is developed by the sensor is present at the ECM. The connectors and the harness inside the terminal box appear to be OK. There may be a problem with the ECM.Repair: It is unlikely that the ECM has failed. Perform

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
D8T TRACK-TYPE TRACTOR MB800001-UP (MACHINE) POWERED BY C15 Engine
D8R TRACK-TYPE TRACTOR JR800001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR JJ500001-UP (MACHINE) POWERED BY C15 Engine
D8R TRACK-TYPE TRACTOR DWJ00001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR AW400001-UP (MACHINE) POWERED BY C15 ENGINE
D8R Custom Parts Manual Track-Type Tractor 7XM00001-UP (MACHINE) POWERED BY 3406 Engine
D8R Custom Parts Manual Track Type Tractor 6YZ00001-UP (MACHINE)
D8R TRACK-TYPE TRACTOR 9EM00001-UP (MACHINE) POWERED BY 3406C Engine
D8T TRACK-TYPE TRACTOR KPZ00001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR J8B00001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR MLN00001-UP (MACHINE) POWERED BY C15 Engine
D8T TRACK-TYPE TRACTOR FCT00001-UP (MACHINE) POWERED BY C15 Engine
D8R TRACK-TYPE TRACTOR RJM00001-UP (MACHINE) POWERED BY 3406C Engine
D8R TRACK-TYPE TRACTOR T5X00001-UP (MACHINE) POWERED BY 3406C Engine
D8T TRACK-TYPE TRACTOR FMC00001-UP (MACHINE) POWERED BY C15 Engine
D8R TRACK-TYPE TRACTOR MEJ00001-UP (MACHINE) POWERED BY 3406C Engine


Parts edge Caterpillar catalog:

9W9098 EDGE-CUTTING
D8N, D8R, D8R II
7T9125 EDGE-CUTTING
844, 844H, 844K, D8N, D8R, D8R II, D9N, D9R, D9T
7T9126 EDGE-CUTTING
D8N, D8R, D8R II
9W6092 EDGE-CUTTING
631E, 631G, 637E, 637G, 844, 844H, 844K, D8N, D8R, D8R II
1122471 EDGE-CUTTING
D10R, D8R, D8R II, D9R, D9T
6Y5540 EDGE-CUTTING
844, 844H, 844K, D8N, D8R, D8R II, D8T, D9N, D9R
4T6381 EDGE-CUTTING
990, 990 II, D10T, D8N, D8R, D8R II, D8T
4T6378 EDGE-CUTTING
631G, 637E, 637G, 844, 844H, 844K, D10T, D8N, D8R, D8R II, D8T
9W5232 EDGE-CUTTING
D8N, D8R, D8R II, D8T
4Z9058 EDGE-CUTTING
D8R, D8R II, D8T
1004046 EDGE-CUTTING
966F, 966F II, 966G, 966G II, 970F
3460500 EDGE GP-BIT & CUTTING
621K, 623G, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC
3460503 EDGE GP-BIT & CUTTING
621K, 623G, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC
2571852 EDGE-CUTTING
814F, 814F II, 816F, 816F II
2571851 EDGE-CUTTING
814F, 814F II, 816F, 816F II, D7R II, D8R II
1073380 EDGE GP-BIT & CUTTING
950G, 950G II, 950H, 962G, 962G II, 962H
1321062 EDGE GP-CUTTING
924K, 930K, 936F, 938F, 938G, 938G II, 938H, 938K, IT38F, IT38G
8J7146 EDGE GP-CUTTING
3P, 3S, D3B, D3C, D4B, D4C
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.