AVSPARE.COM
parts catalog

EDGE- 5087706 - Caterpillar



5087706 EDGE- Caterpillar parts EDGE
Rating:
76
Alternative (cross code) number:
CA5087706
508-7706
5087706
Caterpillar 5087706 EDGE-

Buy EDGE- 5087706 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme:
 
  For full view, you need register

Information:

The soot filter can be cleaned in order to remove oil. Wash the filter in a solution of soap and water. Allow the filter to dry completely before installing the filter.Monitoring the Differential Pressure
A differential pressure gauge can be installed across the air side of the aftercooler core. The differential pressure provides an indication of the amount of plugging in the aftercooler core. The 152-2067 Oil Filter Pressure Differential Gauge Gp is suitable for monitoring the differential pressure. Table 2 lists the components and the locations for connecting the differential pressure gauge.
Table 2
Components and Locations for Sensing the Differential Pressure    
Type of Air Intake System     Hose     Fittings     Location for the Fittings    
Mechanical Unit Injection (MUI)
Rear Turbocharger     5P-1519 Hose and internal 37 degree flare fitting ends     5J-7303 Elbow
8B-2664 Reducer Bushing
001-9440 Connector     Refer to Illustration 1 and Illustration 2    
MUI
Top Turbocharger     5J-7303 Elbow
8B-2664 Reducer Bushing
001-9440 Connector Refer to Illustration 3 and Illustration 4    
Electronic Unit Injection (EUI)
Rear Turbocharger     001-9440 Connector (1) Refer to Illustration 4    
EUI
Top Turbocharger     001-9440 Connector (1) Refer to Illustration 5    
( 1 ) Two Connectors are required
Illustration 1 g01446694
Typical configuration (1) Location for the 5J-7303 Elbow for the high pressure port
Illustration 2 g01446714
Port on a cylinder block (2) Location for the 8B-2664 Reducer Bushing and 001-9440 Connector for the low pressure port
Illustration 3 g01446657
Typical configuration (3) Location for the 5J-7303 Elbow for the high pressure port
Illustration 4 g01446721
Typical configuration (4) Location for the 001-9440 Connector for the low pressure port (5) Location for the 001-9440 Connector for the high pressure port
Illustration 5 g01446991
Typical configuration (6) Location for the 001-9440 Connector for the high pressure port (7) Location for the 001-9440 Connector for the low pressure portTable 3 provides the maximum allowable differential pressure across various components. Perform the appropriate service procedure if the differential pressure exceeds the value that is listed.
Table 3
Maximum Differential Pressure and Service Procedures    
Component    Maximum Differential Pressure    Service Procedure    
Aftercooler Core    
7.5 kPa (30 inches of H2O)     Clean the aftercooler core.    
Air Cleaner Filter    
6.2 kPa (25 inches of H2O)     Clean the soot filter.
Replace the air cleaner filter, if necessary.    
Crankcase     The crankcase pressure must be within
0.5 kPa (2 inch of H2O) of the barometric pressure.     Service the crankcase ventilator filter.
Service the crankcase ventilation system, if necessary.    

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts edge Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.