AVSPARE.COM
parts catalog

EDGE-CUTTING 6J1406 - Caterpillar


6J1406 EDGE-CUTTING Caterpillar parts 5S, 6A, 6S, D6D, D6E, D6E SR, D6G SR
Rating:
50
Alternative (cross code) number:
CA6J1406
6J-1406
6J1406
Caterpillar 6J1406 EDGE-CUTTING
Weight: 5 pounds 2 kg.

Buy EDGE-CUTTING 6J1406 Caterpillar genuine, new aftermarket tractor parts with delivery
BULLDOZER, TRACK-TYPE TRACTOR,

Compatible equipment models: 6J1406:

BULLDOZER  5S   6A   6S  
TRACK-TYPE TRACTOR  D6D   D6E   D6E SR   D6G SR   Caterpillar
Number on catalog scheme: 13
  For full view, you need register
6J1406 Images:
Caterpillar parts 6J1406
Caterpillar parts 6J1406
Caterpillar parts 6J1406
Caterpillar parts 6J1406

Information:


Illustration 1 g01335058
Connections of the transmission clutch solenoid 2
This diagnostic code is associated with the transmission clutch solenoid 2. The FMI 6 means that the ECM has determined that there is a short to ground in the solenoid circuit. The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of SPN 735 FMI 6 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:The FMI 6 changes to FMI 5 when the solenoid is disconnected.Results:
YES - The FMI 6 changes to FMI 5 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Replace the solenoid. Verify that the new solenoid corrects the problem.STOP
NO - The SPN 735 FMI 6 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J2-63 to all other contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-51 and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused by excessive heat, battery acid, or chafing.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit.
Reconnect all harness connectors. Make sure that the harness connectors are fully seated and that the clips for each connector are completely fastened.
Turn the disconnect switch and the key start switch to the ON position.
Operate the vehicle.
Check the status of the SPN 735 FMI 6. Expected Result:The SPN 735 FMI 6 is active.Results:
YES - The SPN 735 FMI 6 is active. The diagnostic code has not been corrected.Repair: Check the circuit again. If the Caterpillar Electronic Technician (Cat ET) is available, use the Cat ET service tool in order to

Caterpillar parts catalog:

Caterpillar parts catalog
D6E Track-Type Tractor SR 8FJ00001-UP (MACHINE) POWERED BY 3306 Engine
D6G Track-Type Tractor Super Rural 3SR00001-UP (MACHINE) POWERED BY 3306 Engine
D6G Track-Type Tractor Power Shift 2MJ02654-UP (MACHINE) POWERED BY 3306 Engine


Parts edge Caterpillar catalog:

7J2778 EDGE GP-BIT & CUTTING
D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 XL
4T3009 EDGE-CUTTING
311C, 311D LRR, 311F LRR, 312C L, 312D, 314C, 314D LCR, 315C, 315D L, 320C, 322C, 325B L, D6E, D6E SR, D6G, D6G SR, D6G2 XL, D6T XL
4T3013 EDGE-CUTTING
D5H, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
4T3010 EDGE-CUTTING
120K, 120K 2, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 3, 140M 3 AWD, 160K, 160M, 160M 3, 160M 3 AWD, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D6H
4T2315 EDGE-CUTTING
D5H, D5R LGP, D6M, D6N, D6N LGP
3G4282 EDGE-CUTTING
527, D5H, D5H XL, D5HTSK II, D5R LGP, D6M, D6N, D6N LGP
1356537 EDGE-CUTTING
D7H, D7R, D7R II, D7R XR
9W6092 EDGE-CUTTING
631E, 631G, 637E, 637G, 844, 844H, 844K, D8N, D8R, D8R II
4T6230 EDGE-CUTTING
D3B, D3C II, D3C III, D3G, D4G, D5G
8E9377 EDGE-CUTTING
525C, 525D, 535C, 535D, 545, 545C, 545D, 555D, D4H XL, D5M, D5N, D6K, D6K LGP, D6K XL
4T8940 EDGE-CUTTING
517, 527, D4H, D4H XL, D5M, D5N, D6K LGP
4T3010 EDGE-CUTTING
120K, 120K 2, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 3, 140M 3 AWD, 160K, 160M, 160M 3, 160M 3 AWD, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D6H
4T3013 EDGE-CUTTING
D5H, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 XL
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.