9J3658 EDGE-CUTTING Caterpillar parts
120M, 12M, 140K, 140M, 140M 2, 14M, 160M, 160M 2
Rating:
Alternative (cross code) number:
CA9J3658
9J-3658
9J3658
CA9J3658
9J-3658
9J3658
Weight: 73 pounds 33 kg.
Information:
BEVEL ANGLE
22.5
BOLT HOLE SIZE
21
mm
HOLE SPACING
152.4
mm
LENGTH
2131.2
mm
NUMBER OF HOLES
15
THICKNESS
15.9
mm
WIDTH
152.4
mm
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Grader Blade fits Caterpillar 9J3658
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
Grader Blade fits Caterpillar 9J3658
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
Compatible equipment models: 9J3658:
Information:
Caterpillar Products: AllIntroduction
Important Safety Information
Illustration 1 g02139237
Think SafetyMost accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.Improper operation, lubrication, maintenance, or repair of this product can be dangerous and could result in injury or death.Do not operate or perform any lubrication, maintenance, or repair on this product until you have read and understood the information.Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons.The hazards are identified by the Safety Alert Symbol and followed by a Signal Word such as "DANGER", "", or "CAUTION". The Safety Alert "" label is shown below.A non-exhaustive list of operations that may cause product damage are identified by "" labels on the product and in this publication.Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are, therefore, not all inclusive. If a tool, procedure, work method, or operating technique is not recommended by Caterpillar, the operator must be sure that the procedure is safe. The operator must also be sure that the product will not be damaged or made unsafe by any unspecified procedures.The information, specifications, and illustrations in this publication are based on information that was available at the time that the publication was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other items can change at any time. These changes can affect the service that is given to the product. Obtain the complete and most current information before you start any job.When replacement parts are required for this product, Caterpillar recommends using Cat replacement parts or parts with equivalent specifications including, but not limited to, physical dimensions, type, strength, and material.Literature Information
This manual contains safety information, operation instructions and maintenance information and should be stored with the tool group.Some photographs or illustrations in this publication may show details that can be different from your service tool. Guards and covers might have been removed for illustrative purposes. Continuing improvement and advancement of product design might have caused changes to your service tool, which are not included in this publication.Whenever a question arises regarding your service tool or this publication, consult Dealer Service Tools (DST) for the latest available information.Safety Section
The Safety section lists basic safety precautions.Read and understand the basic precautions listed in the Safety section before operating or performing maintenance and repair on this service tool.General Information Section
The General Information section describes tooling functions and features. The section provides useful information on individual parts, additional tooling, and resources.Operation Section
The Operation section is a reference for the new operator and a refresher for the experienced operator.Photographs and illustrations
Important Safety Information
Illustration 1 g02139237
Think SafetyMost accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.Improper operation, lubrication, maintenance, or repair of this product can be dangerous and could result in injury or death.Do not operate or perform any lubrication, maintenance, or repair on this product until you have read and understood the information.Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons.The hazards are identified by the Safety Alert Symbol and followed by a Signal Word such as "DANGER", "", or "CAUTION". The Safety Alert "" label is shown below.A non-exhaustive list of operations that may cause product damage are identified by "" labels on the product and in this publication.Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The warnings in this publication and on the product are, therefore, not all inclusive. If a tool, procedure, work method, or operating technique is not recommended by Caterpillar, the operator must be sure that the procedure is safe. The operator must also be sure that the product will not be damaged or made unsafe by any unspecified procedures.The information, specifications, and illustrations in this publication are based on information that was available at the time that the publication was written. The specifications, torques, pressures, measurements, adjustments, illustrations, and other items can change at any time. These changes can affect the service that is given to the product. Obtain the complete and most current information before you start any job.When replacement parts are required for this product, Caterpillar recommends using Cat replacement parts or parts with equivalent specifications including, but not limited to, physical dimensions, type, strength, and material.Literature Information
This manual contains safety information, operation instructions and maintenance information and should be stored with the tool group.Some photographs or illustrations in this publication may show details that can be different from your service tool. Guards and covers might have been removed for illustrative purposes. Continuing improvement and advancement of product design might have caused changes to your service tool, which are not included in this publication.Whenever a question arises regarding your service tool or this publication, consult Dealer Service Tools (DST) for the latest available information.Safety Section
The Safety section lists basic safety precautions.Read and understand the basic precautions listed in the Safety section before operating or performing maintenance and repair on this service tool.General Information Section
The General Information section describes tooling functions and features. The section provides useful information on individual parts, additional tooling, and resources.Operation Section
The Operation section is a reference for the new operator and a refresher for the experienced operator.Photographs and illustrations
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
4T2236
EDGE-CUTTING
14G, 14H, 14H NA, 14M, 160H, 160H NA, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 163H NA, 16G, 16H, 16H NA, 16M
14G, 14H, 14H NA, 14M, 160H, 160H NA, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 163H NA, 16G, 16H, 16H NA, 16M
4T3010
EDGE-CUTTING
120K, 120K 2, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 3, 140M 3 AWD, 160K, 160M, 160M 3, 160M 3 AWD, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D6H
120K, 120K 2, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 3, 140M 3 AWD, 160K, 160M, 160M 3, 160M 3 AWD, D6D, D6E, D6E SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D6H
4T3028
EDGE-CUTTING
120H NA, 12H NA, 135H NA, 140H NA, 140M, 143H, 14M, 160H NA, 160M, 163H NA, SNOW WING
120H NA, 12H NA, 135H NA, 140H NA, 140M, 143H, 14M, 160H NA, 160M, 163H NA, SNOW WING
7D1158
EDGE
120M, 12M, 140H, 140H ES, 140H NA, 140K, 140M, 143H, 14G, 14H, 14H NA, 14M, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 16G
120M, 12M, 140H, 140H ES, 140H NA, 140K, 140M, 143H, 14G, 14H, 14H NA, 14M, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 16G
8J9821
EDGE
14G, 14H, 14H NA, 14M, 160H, 160H NA, 160M, 160M 2, 163H, 163H NA, 16G
14G, 14H, 14H NA, 14M, 160H, 160H NA, 160M, 160M 2, 163H, 163H NA, 16G
7D1949
EDGE-CUTTING
14G, 14M, 160H, 160M, 160M 2, 163H, 163H NA, 16G
14G, 14M, 160H, 160M, 160M 2, 163H, 163H NA, 16G
9J7701
EDGE-CUTTING
120M, 12M, 140H ES, 140H NA, 140M, 143H, 160H, 160H ES, 160H NA, 160M, 163H NA
120M, 12M, 140H ES, 140H NA, 140M, 143H, 160H, 160H ES, 160H NA, 160M, 163H NA
7D1576
EDGE-CUTTING
120H, 120K, 120K 2, 120M, 12H, 12K, 12M, 135H, 140H, 140H ES, 140H NA, 140M, 143H, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA
120H, 120K, 120K 2, 120M, 12H, 12K, 12M, 135H, 140H, 140H ES, 140H NA, 140M, 143H, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA
7D1577
EDGE-CUTTING
120K, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14M, 160H, 160H ES, 160H NA, 160K, 160M, 160M 2, 160M 3, ...
120K, 120M, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14M, 160H, 160H ES, 160H NA, 160K, 160M, 160M 2, 160M 3, ...
3G2165
EDGE-CUTTING
120M, 120M 2, 12H ES, 12M, 12M 2, 12M 3, 12M 3 AWD, 140H, 140H ES, 140H NA, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 163H NA, 16G, ...
120M, 120M 2, 12H ES, 12M, 12M 2, 12M 3, 12M 3 AWD, 140H, 140H ES, 140H NA, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 163H NA, 16G, ...
4T2968
EDGE-CUTTING
12M 2, 140M, 14M, 160M, SNOW WING
12M 2, 140M, 14M, 160M, SNOW WING
9J3657
EDGE-CUTTING
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD
4T2968
EDGE-CUTTING
12M 2, 140M, 14M, 160M, SNOW WING
12M 2, 140M, 14M, 160M, SNOW WING
2419472
EDGE-CUTTING
BP18B, BU115, BU118
BP18B, BU115, BU118
2419437
EDGE-CUTTING
BP18B, BU115, BU118
BP18B, BU115, BU118
3224714
EDGE-CUTTING
MP318, S365B, VHS-60/3
MP318, S365B, VHS-60/3
3224713
EDGE-CUTTING
S365B, VHS-60/3
S365B, VHS-60/3
3224712
EDGE-CUTTING
S365B, VHS-60/3
S365B, VHS-60/3
3435980
EDGE-CUTTING
CTV15
CTV15
4T3029
EDGE-CUTTING
14M, SNOW WING
14M, SNOW WING
4T2967
EDGE-CUTTING
SNOW WING
SNOW WING
1694089
EDGE-CUTTING
120K, 120K 2, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 3, 140M 3 AWD, 160K, 160M, 160M 3, 160M 3 AWD
120K, 120K 2, 120M, 12K, 12M, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 3, 140M 3 AWD, 160K, 160M, 160M 3, 160M 3 AWD
2322146
EDGE-CUTTING
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD
9J3657
EDGE-CUTTING
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD