9U8079 EDGE GP Caterpillar parts
D5H XL, D5R LGP, D6M, D6N, D6N LGP
Rating:
Alternative (cross code) number:
CA9U8079
9U-8079
9U8079
CA9U8079
9U-8079
9U8079
Weight: 11 pounds 4 kg.
TRACK-TYPE TRACTOR,
Information:
Start By:
Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
Remove the rocker arms and the rocker shafts. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Remove".Note: This is an optional procedure to remove the camshaft. The preceding tool list shows the required tooling for removing the camshaft from the front of the engine or the rear of the engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 10 g01028806
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Remove bolts (2) and thrust plate (1) .
Illustration 11 g00576209
Remove seal assembly (3) and adapter (4) .
Illustration 12 g00576240
Remove O-ring seals (5) and (6) from seal assembly (3) .
Illustration 13 g01043575
Remove screws (7) and cover (8) .
Care must be used when removing the camshaft to not damage the highly finshed surfaces of both the camshaft and camshaft bearings
Illustration 14 g01024825
Note: Carefully align Tooling (F) with the end of the camshaft. If the adapter and the camshaft are not aligned, the camshaft may not be removed. The adapter and camshaft bearing will interfere.
To remove the camshaft from the rear of the engine, install Tooling (F) on the front of the camshaft with Tooling (G) .
Install Tooling (E) .
Illustration 15 g01043577
Carefully slide the camshaft to the rear of the engine for removal. Use two technicians to remove the camshaft. Keep the camshaft level while the camshaft is being removed from the cylinder head. The weight of the camshaft is approximately 39 kg (86 lb).
Illustration 16 g01024826
To remove the camshaft from the front of the engine, install Tooling (E) on the rear of the camshaft.
Carefully slide the camshaft to the front of the engine for removal. Use two technicians to remove the camshaft. Keep the camshaft level while the camshaft is being removed from the cylinder head. The weight of the camshaft is approximately 39 kg (86 lb).
Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
Remove the rocker arms and the rocker shafts. Refer to Disassembly and Assembly, "Rocker Arm and Shaft - Remove".Note: This is an optional procedure to remove the camshaft. The preceding tool list shows the required tooling for removing the camshaft from the front of the engine or the rear of the engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 10 g01028806
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Remove bolts (2) and thrust plate (1) .
Illustration 11 g00576209
Remove seal assembly (3) and adapter (4) .
Illustration 12 g00576240
Remove O-ring seals (5) and (6) from seal assembly (3) .
Illustration 13 g01043575
Remove screws (7) and cover (8) .
Care must be used when removing the camshaft to not damage the highly finshed surfaces of both the camshaft and camshaft bearings
Illustration 14 g01024825
Note: Carefully align Tooling (F) with the end of the camshaft. If the adapter and the camshaft are not aligned, the camshaft may not be removed. The adapter and camshaft bearing will interfere.
To remove the camshaft from the rear of the engine, install Tooling (F) on the front of the camshaft with Tooling (G) .
Install Tooling (E) .
Illustration 15 g01043577
Carefully slide the camshaft to the rear of the engine for removal. Use two technicians to remove the camshaft. Keep the camshaft level while the camshaft is being removed from the cylinder head. The weight of the camshaft is approximately 39 kg (86 lb).
Illustration 16 g01024826
To remove the camshaft from the front of the engine, install Tooling (E) on the rear of the camshaft.
Carefully slide the camshaft to the front of the engine for removal. Use two technicians to remove the camshaft. Keep the camshaft level while the camshaft is being removed from the cylinder head. The weight of the camshaft is approximately 39 kg (86 lb).
Caterpillar SIS machinery equipment:
Caterpillar SIS
D5R2 XL Track-Type Tractor R5A00001-UP (MACHINE) POWERED BY C7.1 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N XL, LGP TRACK-TYPE TRACTOR NJN00001-UP (MACHINE) POWERED BY C7.1 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N XL Track-Type Tractor P5S00001-UP (MACHINE) POWERED BY C7.1 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D5H Track-Type Tractor Power Shift XL 8RJ00001-UP (MACHINE) POWERED BY 3304 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6M & D6M LGP Track-Type Tractor 2RN00001-UP (MACHINE) POWERED BY 3116 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6M TRACK-TYPE TRACTOR XL, LGP 3WN00001-UP (MACHINE) POWERED BY 3116 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N XL, FTC, LGP TRACK-TYPE TRACTOR ALH00001-UP (MACHINE) POWERED BY 3126B Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N XL, D/S, LGP TRACK-TYPE TRACTOR AKM00001-UP (MACHINE) POWERED BY 3126B Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N TRACK-TYPE TRACTOR XL Differential Steering CCK00001-UP (MACHINE) POWERED BY 3126B Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N XL, FTC TRACK-TYPE TRACTOR CBJ00001-UP (MACHINE) POWERED BY 3126B Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N TRACK-TYPE TRACTOR XL, LGP Differential Steering DJA00001-UP (MACHINE) POWERED BY C6.6 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N TRACK-TYPE TRACTOR XL JAH00001-UP (MACHINE) POWERED BY C6.6 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N XL, LGP Differential Steering, Electrohydraulic Implement TRACK-TYPE TRACTOR GHS00001-UP (MACHINE) POWERED BY C6.6 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N XL Differential Steering, Electrohydraulic Implement TRACK-TYPE TRACTOR LJR00001-UP (MACHINE) POWERED BY C6.6 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N TRACK-TYPE TRACTOR XL, LGP PBA00001-UP (MACHINE) POWERED BY C6.6 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D5R XL, LGP Differential Steering, Electrohydraulic Implement TRACK-TYPE TRACTOR D5L00001-UP (MACHINE) POWERED BY C6.6 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6N TRACK-TYPE TRACTOR XL, LGP GB600001-UP (MACHINE) POWERED BY C7.1 Engine »
9U-8079
EDGE GP-BIT & CUTTING
D6M TRACK-TYPE TRACTOR CUSTOM PARTS MANUAL-POWER SHIFT, LOW 2RN00001-UP (MACHINE) »
9U-8079
EDGE GP
D6M TRACK-TYPE TRACTOR CUSTOM PARTS MANUAL-POWER SHIFT, LOW 2RN00001-UP (MACHINE) »
9U-8079
EDGE GP
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
4T6659
EDGE-CUTTING
321C, 321D LCR, D5H XL, D5R LGP, D6H, D6M, D6N, D6N LGP, D6R, D6R II, D6T XL
321C, 321D LCR, D5H XL, D5R LGP, D6H, D6M, D6N, D6N LGP, D6R, D6R II, D6T XL
4T2952
EDGE-CUTTING
D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL
D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL
9U8057
EDGE - CUTTING
D5H XL, D5R LGP, D6M, D6N, D6N LGP, D6R II
D5H XL, D5R LGP, D6M, D6N, D6N LGP, D6R II
1U2211
EDGE-CUTTING
D5H, D6M, D6N
D5H, D6M, D6N
3G4282
EDGE-CUTTING
527, D5H, D5H XL, D5HTSK II, D5R LGP, D6M, D6N, D6N LGP
527, D5H, D5H XL, D5HTSK II, D5R LGP, D6M, D6N, D6N LGP
4T2315
EDGE-CUTTING
D5H, D5R LGP, D6M, D6N, D6N LGP
D5H, D5R LGP, D6M, D6N, D6N LGP
2570264
EDGE-CUTTING
D6N, D6N LGP
D6N, D6N LGP
2570265
EDGE-CUTTING
D6N, D6N LGP
D6N, D6N LGP
2782168
EDGE-CUTTING
D6N, D6N LGP
D6N, D6N LGP
2782169
EDGE-CUTTING
D6N, D6N LGP
D6N, D6N LGP
9W9700
EDGE GP-BIT & CUTTING
651E, 657E, 657G
651E, 657E, 657G
1601577
EDGE GP-CUTTING
525C, 525D, 535C, 535D, 545, 545C, 545D, 555D
525C, 525D, 535C, 535D, 545, 545C, 545D, 555D
2227589
EDGE GP-BIT & CUTTING
621G, 627F, 627G
621G, 627F, 627G
2227587
EDGE GP-BIT & CUTTING
621G, 627F, 627G
621G, 627F, 627G
1670316
EDGE GP-CUTTING
311C, 311D LRR, 311F LRR, 312C L, 312D, 314C, 314D LCR, 315C, 315D L
311C, 311D LRR, 311F LRR, 312C L, 312D, 314C, 314D LCR, 315C, 315D L
2227583
EDGE GP-BIT & CUTTING
621G, 627F, 627G
621G, 627F, 627G
9D2170
EDGE GP-CUTTING
14G, 14H, 14H NA
14G, 14H, 14H NA
4370288
EDGE GP-CUTTING
950K, 962K
950K, 962K
6Y6754
EDGE GP-SEGMENT
931C II, 933, 933C, 935C II
931C II, 933, 933C, 935C II
2464804
EDGE GP-CUTTING
902C, 903C
902C, 903C
3116640
EDGE-CUTTING
621G, 627G
621G, 627G
2367179
EDGE-CUTTING
657E, 657G
657E, 657G