AVSPARE.COM
parts catalog

EDGE-CUTTING 9V9072 - Caterpillar



9V9072 EDGE-CUTTING Caterpillar parts 936, 936F, G936 EDGE
Rating:
66
Alternative (cross code) number:
CA9V9072
9V-9072
9V9072
Caterpillar 9V9072 EDGE-CUTTING
Weight: 389 pounds 176 kg.

Buy EDGE-CUTTING 9V9072 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 9V9072:

WHEEL LOADER  936   936F   G936   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:


Do not fill the secondary fuel filter with fuel before installing. The fuel would not be filtered and could be contaminated. Contaminated fuel will cause accelerated wear to fuel system parts.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Before you replace the secondary fuel filter, the primary fuel filter must be replaced. Refer to the Operation and Maintenance Manual, "Fuel System Primary Filter - Clean/Inspect/Replace".
Park the machine on a level surface. Ensure that the parking brake is fully engaged. Lower the dump body and stop the engine.
Raise the hood.
Illustration 1 g00603568
Use a strap wrench and remove the secondary fuel filter. Discard the secondary fuel filter properly.
Clean the fuel filter base. Ensure that all of the old filter base gasket is removed.
Coat the new filter base gasket for the new secondary fuel filter with clean diesel fuel prior to installation.
Install the new secondary fuel filter by hand. Do not use a tool for installation of the secondary fuel filter. When the new filter base gasket contacts the fuel filter base, tighten the secondary fuel filter by an additional 270°.Rotation index marks are positioned on the secondary fuel filter at 90° intervals. Use the rotation index marks as a guide when you tighten the secondary fuel filter.
Prime the fuel system.Refer to the Operation and Maintenance Manual, "Fuel System - Prime".
Start the engine and check for leaks.
Lower the hood.

Caterpillar parts catalog:

Caterpillar parts catalog
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE
936E WHEEL LOADER 45Z03057-UP (MACHINE) POWERED BY 3304 ENGINE
936F WHEEL LOADER 4TK00001-UP (MACHINE) POWERED BY 3304 ENGINE
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE
936E WHEEL LOADER 45Z03057-UP (MACHINE) POWERED BY 3304 ENGINE
G936 WHEEL LOADER 8ED00001-UP (MACHINE) POWERED BY 3304 ENGINE
936 WHEEL LOADER 4SB00001-01623 (MACHINE) POWERED BY 3304 ENGINE
936E WHEEL LOADER 4SB01624-02502 (MACHINE) POWERED BY 3304 ENGINE
936E WHEEL LOADER 4SB02503-UP (MACHINE) POWERED BY 3304 ENGINE


Parts edge Caterpillar catalog:

9W3481 EDGE-END-RH
926A, 928G, 936, 938F, 938G, IT12B, IT28G, IT38G
4T6693 EDGE-SEGMENT
930R, 936, 936F, 943, 955L, IT24F
9W3482 EDGE-CUTTING-LH
926A, 928G, 936, 938F, 938G, IT12B, IT28G, IT38G
4T8091 Edge-End
910G, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 928F, 928G, 928HZ, 930G, 930K, 936, 936F, 938F, 938G, 938G II, 938H, 938K, 939, 939C, 943, 950K, 953, 953C, 953D, 962K, IT12B, IT14G, IT18F, IT24F, IT...
4T6694 EDGE-SEGMENT
918F, 924F, 924GZ, 924H, 924HZ, 926, 928G, 928HZ, 930G, 930R, 936, 936F, 938F, 938H, 953, 953C, 963, 963B, 963C, 963D, IT24F, IT28F, IT28G
1321037 EDGE-SEGMENT
924F, 924K, 930K, 936F, 938F, 938G, 938G II, 938H, 938K, 953C, IT24F, IT28F, IT28G, IT38F, IT38G
1U0607 EDGE-CUTTING
920, 930, 936, 936F, 938H, IT24F
1052345 EDGE-CUTTING
928HZ, 930G, 936F, 938F, 938G, 938G II, 938H, 966M XE, 972M XE, IT38F, IT38G, IT38G II, IT38H
4T6695 EDGE-SEGMENT
924K, 930K, 936, 938F, 938G, 938G II, 938H, 938K, 950B, 950B/950E, 950F, 950F II, 960F, 966F II, G936, IT38F, IT38G, IT38G II
6W2985 EDGE-CUTTING
936, 936F, G936
6W2984 EDGE-CUTTING
930R, 936, 936F
6W2985 EDGE-CUTTING
936, 936F, G936
6W2984 EDGE-CUTTING
930R, 936, 936F
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.