9W6609 EDGE-CUTTING Caterpillar parts
966H, D10N, D10R, D10T
Rating:
Alternative (cross code) number:
CA9W6609
9W-6609
9W6609
CA9W6609
9W-6609
9W6609
Weight: 224 pounds 101 kg.
Information:
ABRASION RESISTANT MATERIAL
N
BOLT HOLE SIZE
36.5
mm
CHAMFER
EDGE
HOLE PATTERN
CENTERLINE
HOLE SPACING
152.4
mm
LENGTH
992
mm
NUMBER OF HOLES
6
THICKNESS
35
mm
TUNGSTEN CARBIDE
N
WIDTH
406
mm
TRACK-TYPE TRACTOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 9W6609 Bulldozer Blade for Model D10, Center Edge, 1.38" Edge Thickness
CTP For Model D10 || Center Edge || 1.38" Edge Thickness
CTP For Model D10 || Center Edge || 1.38" Edge Thickness
CTP 9W6609 Bulldozer Blade for Model D10, Center Edge, 1.38" Edge Thickness
CTP For Model D10 || Center Edge || 1.38" Edge Thickness
CTP For Model D10 || Center Edge || 1.38" Edge Thickness
This part in 2 request:
Show.
This information for suppliers only!
2024-08-13
2022-10-24
Compatible equipment models: 9W6609:
Information:
Installation Procedure
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not remove the priority valve while the engine is hot. Hot oil can cause burns.
Illustration 1 g00609688
Replace the O-ring seals (8) on the front housing.
Illustration 2 g00609676
Illustration 3 g00609681
This is an Illustration of a priority valve that is not covered by tubes and lines.
Replace the priority valve on the front housing.
Replace six bolts (7).
Replace the clamp bolt (4).
Replace the bolts in order to connect the tube (7).
Replace the tube (1) on the priority valve.
Replace the clamp bolt (2).
Pull the elbow assembly downward in order to allow clearance for the priority valve to be replaced. Lubricate the seals before installation.
Connect the elbow (3).
Connect the tube (5).
Close the drain valve on the oil filters.
Check the engine oil level. Refer to the Operation And Maintenance Manual.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not remove the priority valve while the engine is hot. Hot oil can cause burns.
Illustration 1 g00609688
Replace the O-ring seals (8) on the front housing.
Illustration 2 g00609676
Illustration 3 g00609681
This is an Illustration of a priority valve that is not covered by tubes and lines.
Replace the priority valve on the front housing.
Replace six bolts (7).
Replace the clamp bolt (4).
Replace the bolts in order to connect the tube (7).
Replace the tube (1) on the priority valve.
Replace the clamp bolt (2).
Pull the elbow assembly downward in order to allow clearance for the priority valve to be replaced. Lubricate the seals before installation.
Connect the elbow (3).
Connect the tube (5).
Close the drain valve on the oil filters.
Check the engine oil level. Refer to the Operation And Maintenance Manual.
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
1359546
EDGE-SEGMENT
374D L, 374F L, 966G, 966G II, 966H, 966K, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE
374D L, 374F L, 966G, 966G II, 966H, 966K, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE
1359545
EDGE-SEGMENT
374D L, 374F L, 966G, 966G II, 966H, 966K, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE
374D L, 374F L, 966G, 966G II, 966H, 966K, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE
9W6615
EDGE-CUTTING
966H, 966K, 972G II, 972H, 972K, 972M, D10N, D10R, D10T
966H, 966K, 972G II, 972H, 972K, 972M, D10N, D10R, D10T
1122472
EDGE-CUTTING
D10R, D8R, D8R II
D10R, D8R, D8R II
9W6608
EDGE-CUTTING
D10N, D10R, D10T
D10N, D10R, D10T
9W6657
EDGE-CUTTING
854G, 854K, D10N, D10R, D10T, D10T2
854G, 854K, D10N, D10R, D10T, D10T2
9W6658
EDGE-CUTTING
854G, 854K, D10N, D10R, D10T, D10T2
854G, 854K, D10N, D10R, D10T, D10T2
9W6656
EDGE-CUTTING
854G, D10N, D10R, D10T, D10T2
854G, D10N, D10R, D10T, D10T2
7J2980
EDGE-CUTTING
9A, 9S, D10T, D9L
9A, 9S, D10T, D9L
4T6385
EDGE-CUTTING
D10T
D10T
8E2085
EDGE-CUTTING
D10T, D10T2
D10T, D10T2
8E2086
EDGE-CUTTING
D10T, D10T2
D10T, D10T2
2494705
EDGE GP
966H
966H
2915308
EDGE AS
966H, 972H, 972K
966H, 972H, 972K
2493172
EDGE GP-CUTTING
966H, 966K, 972H
966H, 966K, 972H
2687460
EDGE-CUTTING
966H
966H
2629100
EDGE GP-CUTTING
966H, 972H
966H, 972H
2494703
EDGE GP-CUTTING
966H, 972H
966H, 972H
3194043
EDGE AS-BASE
990H
990H
2436342
EDGE AS-CUTTING
972H, 972K
972H, 972K
2904606
EDGE
966H
966H
2663443
EDGE AS-LEVELING
966H, 972H
966H, 972H
3550017
EDGE AS
966H, 966K, 966M, 966M XE, 972H, 972K, 972M, 972M XE, 980K
966H, 966K, 966M, 966M XE, 972H, 972K, 972M, 972M XE, 980K