9W6656 EDGE-CUTTING Caterpillar parts
854G, D10N, D10R, D10T, D10T2
Rating:
Alternative (cross code) number:
CA9W6656
9W-6656
9W6656
CA9W6656
9W-6656
9W6656
Weight: 287 pounds 130 kg.
Information:
ABRASION RESISTANT MATERIAL
N
BOLT HOLE SIZE
36.5
mm
CHAMFER
EDGE
HOLE PATTERN
CENTERLINE
HOLE SPACING
152.4
mm
LENGTH
992
mm
NUMBER OF HOLES
6
THICKNESS
45
mm
TUNGSTEN CARBIDE
N
WIDTH
406
mm
TRACK-TYPE TRACTOR, WHEEL DOZER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 9W6656 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each
CTP For Ground Engaging Tools || Longer tips || Sold in each
CTP 9W6656 Ground Engaging Tools Cutting Edge
CTP For Ground Engaging Tools || Longer tips || Sold in each
CTP For Ground Engaging Tools || Longer tips || Sold in each
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 9W6656:
Information:
Because the strength of the frame may decrease, some manufacturers do not recommend welding onto a chassis frame or rail. Consult the OEM of the equipment or your Caterpillar dealer regarding welding on a chassis frame or rail.
To help avoid damage to the electronic controls, proper welding procedures are necessary. Before you weld on equipment with electronic controls, observe the following precautions:
Turn off the engine. Place the engine control switch in the OFF position.
If the engine has a battery disconnect switch, open the switch. Otherwise, disconnect the negative "-" battery cable from the battery of the equipment.
Do not ground the welder to electrical components such as the ECM or sensors. Improper grounding can cause damage to the drive train bearings, hydraulic components, electrical components, and other components.Clamp the ground cable from the welder to the component that will be welded. Place the clamp as close as possible to the weld. This will help reduce the possibility of damage.
Clamp the ground cable from the welder to the component that will be welded. Place the clamp as close as possible to the weld.
Protect wiring harnesses from welding debris and from spatter. Use proper welding procedures.
Caterpillar parts catalog:
Parts edge Caterpillar catalog:
966H, 966K, 972G II, 972H, 972K, 972M, D10N, D10R, D10T
966H, D10N, D10R, D10T
854G, D11R, D9L
D10R, D8R, D8R II
D10N, D10R, D10T
854G, 854K, D10N, D10R, D10T, D10T2
854G, 854K, D10N, D10R, D10T, D10T2
854G, D9L
9A, 9S, D10T, D9L
D10T
D10T, D10T2
D10T, D10T2
8E3581
EDGE
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
1099050
EDGE-CUTTING
D11N, D11R
D11N, D11R
1099047
EDGE AS
D11N, D11R
D11N, D11R
1073523
EDGE-CUTTING
D11N, D11R
D11N, D11R
824C
1099096
EDGE-CUTTING
824C
824C
1130322
EDGE-CUTTING
834G, D9R
834G, D9R
D9N, D9R
834G, 834H, 834K, D9N, D9R
1130338
EDGE AS
D10N, D10R
D10N, D10R
1073510
EDGE-CUTTING
D10N, D10R
D10N, D10R