7N1760 EJECTOR AS Caterpillar parts
824C, 826C, 980C, 980F
Rating:
Alternative (cross code) number:
CA7N1760
7N-1760
7N1760
CA7N1760
7N-1760
7N1760
Weight: 16 pounds 7 kg.
LANDFILL COMPACTOR, WHEEL LOADER,
Related part:
7N1760
EJECTOR-AS-YM
3731914
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
7N1760 pipee Fits Catterpillarr 824C 826C 980C 980F
SOLOGEAR Part Number: 7N1760
SOLOGEAR Part Number: 7N1760
CTP 7N1760 Air Inlet/Exhaust Pipe for Models 824C, 826C, 980C, 980F
CTP For Models 824C, 826C, 980C, 980F || Highly Efficient || Easy in-and-out fit
CTP For Models 824C, 826C, 980C, 980F || Highly Efficient || Easy in-and-out fit
RAParts New Aftermarket 7N1760 Pipe Exhaust Fits Caterpillar 824C 826C 980C 980F
Reliable Aftermarket Parts New Aftermarket Exhaust Pipe || Fits Caterpillar Models 824C, 826C, 980C, 980F || Replaces Part Number: 7N1760 || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering.
Reliable Aftermarket Parts New Aftermarket Exhaust Pipe || Fits Caterpillar Models 824C, 826C, 980C, 980F || Replaces Part Number: 7N1760 || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering.
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 7N1760:
Information:
In order to find the cause of an engine overspeed shutdown, perform this procedure.
Check setpoints.This step checks setpoints P09 (ring gear teeth) and P10 (engine overspeed).
View the setpoints and note the setpoints P09 and P10. See Systems Operation, "Engine/Generator Setpoint Viewing OP2".
Compare the setpoints that are viewed with the specified setpoints of the particular generator set.Expected Result: The setpoint value that is viewed and the setpoint value that is specified should agree.Results:
OK - Proceed to 2.
Not OK - The setpoints do not agree. Reprogram setpoints P09, P10 and P14. See Systems Operation, "Engine/Generator Programming OP5". STOP.
Check for possible causes.
Check for the possible causes of the engine overspeed condition. Refer to the Engine Service Manual and/or the Governor Service Manuals.Expected Result: No cause should be found.Results:
OK - Proceed to 3.
Not OK - The cause is found. Repair engine components or replace engine components. If necessary, repair governor components or replace governor components. STOP.
Check the engine overspeed function.Note: Take precautions in order to stop the engine manually when you are performing this step.
When possible, disable the engine from reaching rated speed.
Turn the ECS to the OFF/RESET position and then turn the ECS to the START position.
Slowly increase the RPM to rated speed.Expected Result: The engine should not overspeed. The GSC should not shut down the engine. The GSC should not issue an overspeed fault.Results:
OK - The engine reaches rated speed, the GSC does not issue an overspeed fault and the GSC does not shut down the engine. The GSC and the system are functioning properly. Perform a verification of an overspeed. See Systems Operation, "Engine Setpoint Verification OP9". STOP.
Not OK - The engine overspeeds and the GSC issues an overspeed fault. Refer to the Engine Service Manual and/or the Governor Service Manual in order to find the cause of the problem. STOP.
Check setpoints.This step checks setpoints P09 (ring gear teeth) and P10 (engine overspeed).
View the setpoints and note the setpoints P09 and P10. See Systems Operation, "Engine/Generator Setpoint Viewing OP2".
Compare the setpoints that are viewed with the specified setpoints of the particular generator set.Expected Result: The setpoint value that is viewed and the setpoint value that is specified should agree.Results:
OK - Proceed to 2.
Not OK - The setpoints do not agree. Reprogram setpoints P09, P10 and P14. See Systems Operation, "Engine/Generator Programming OP5". STOP.
Check for possible causes.
Check for the possible causes of the engine overspeed condition. Refer to the Engine Service Manual and/or the Governor Service Manuals.Expected Result: No cause should be found.Results:
OK - Proceed to 3.
Not OK - The cause is found. Repair engine components or replace engine components. If necessary, repair governor components or replace governor components. STOP.
Check the engine overspeed function.Note: Take precautions in order to stop the engine manually when you are performing this step.
When possible, disable the engine from reaching rated speed.
Turn the ECS to the OFF/RESET position and then turn the ECS to the START position.
Slowly increase the RPM to rated speed.Expected Result: The engine should not overspeed. The GSC should not shut down the engine. The GSC should not issue an overspeed fault.Results:
OK - The engine reaches rated speed, the GSC does not issue an overspeed fault and the GSC does not shut down the engine. The GSC and the system are functioning properly. Perform a verification of an overspeed. See Systems Operation, "Engine Setpoint Verification OP9". STOP.
Not OK - The engine overspeeds and the GSC issues an overspeed fault. Refer to the Engine Service Manual and/or the Governor Service Manual in order to find the cause of the problem. STOP.
Caterpillar parts catalog:
Parts ejector Caterpillar catalog:
1953068
EJECTOR AS
814F, 814F II, 815F, 815F II, 816F, 816F II, 980C
814F, 814F II, 815F, 815F II, 816F, 816F II, 980C
3650399
EJECTOR AS
980K
980K
3555905
EJECTOR AS-DUST
966K, 972K
966K, 972K
1953068
EJECTOR AS
814F, 814F II, 815F, 815F II, 816F, 816F II, 980C
814F, 814F II, 815F, 815F II, 816F, 816F II, 980C
1335935
EJECTOR AS-DUST
994D, 994F, 994H
994D, 994F, 994H
988F, 988F II