8N4551 EJECTOR ASSEM. Caterpillar parts
D10
Rating:
Alternative (cross code) number:
CA8N4551
8N-4551
8N4551
CA8N4551
8N-4551
8N4551
Weight: 23 pounds 10 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 8N4551:
Number on catalog scheme:
2
For full view, you need register
Information:
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01431548
Attach a suitable lifting device to piston pump (5). The weight of piston pump (5) is approximately 170 kg (375 lb).
Install the O-ring seal, piston pump (5), and bolts (4).
Illustration 2 g01431546
Connect harness assembly (2) and all hose assemblies (3).
Illustration 3 g01431545
Close center door assemblies (1).
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01431548
Attach a suitable lifting device to piston pump (5). The weight of piston pump (5) is approximately 170 kg (375 lb).
Install the O-ring seal, piston pump (5), and bolts (4).
Illustration 2 g01431546
Connect harness assembly (2) and all hose assemblies (3).
Illustration 3 g01431545
Close center door assemblies (1).
Caterpillar parts catalog:
Parts ejector Caterpillar catalog:
3357292
EJECTOR AS
D10T2, D11T
D10T2, D11T
16H, D8T
D10N, D10R, D10T, D11R, D11T
2199914
EJECTOR AS
D10N, D10R, D10T
D10N, D10R, D10T
140H, 143H, 14H NA, 160H, 163H NA
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 160H, 160H ES, 160H NA
