AVSPARE.COM
parts catalog

ELBOW 0544526 - Caterpillar



0544526 ELBOW Caterpillar parts ELBOW
Rating:
71
Alternative (cross code) number:
CA0544526
054-4526
0544526
Caterpillar 0544526 ELBOW
Weight: 0.20 pounds 0 kg.

Buy ELBOW 0544526 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Disconnect switch to remove possibility of disconnecting alarm. This is an interim corrective action before permanent corrective action (with alarm status monitor) is available.
See the attached procedure.
OWNER NOTIFICATION
U.S. and Canadian owners will receive the attached Owner Notification.
SERVICE CLAIM ALLOWANCES
Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
100% 100% 0% 0% 0% 0%
This is a 1.0-hour job
PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE.
COPY OF OWNER NOTIFICATION FOR U.S. AND CANADIAN OWNERS
XYZ Corporation
3240 Arrow Drive
Anywhere, YZ 99999
SAFETY - PRODUCT IMPROVEMENT PROGRAM TO REMOVE STABILITY ALARM SWITCH ON CERTAIN 325D,
330D, 345C, AND 385CL EXCAVATORS (DEMOLITION CORE)
MODELS INVOLVED - 325D, 330D, 345C, 365C, and 385C
Dear Caterpillar Product Owner:
The existing wiring harness on the products listed below needs to be modified to prevent the disconnection of the stability alarm. Unintended and/or unnoticed disconnection of this alarm could lead to incorrect operation of the machine with the loss of machine stability with the potential for serious injury or death. You will not be charged for the service performed.
Contact your local Caterpillar dealer immediately to schedule this service. The dealer will advise you of the time required to complete this service.
Please refer the dealer to their Service Letter dated 15Feb2007 when scheduling this service.
We regret the inconvenience this may cause you, but urge you to have this service performed for your added safety and satisfaction.
Caterpillar Inc.
Identification #(s)
Attached to 15Feb2007 Service Letter
Rework Procedure
In cab, at rear of RH armrest, disconnect and cut the two terminals connected to 283-3074 Switch in cab (switch is located in rear central position, 568-GN & H414-YL wires).
There should be also two (325D, 330D and 345C) or three other (365C, 385C) switches located in this area (on the first row of plate towards front of machine). These are used for back-up mode. Do not disconnect or remove any of these switches.
Remove 283-3074 Switch (located in rear central position).
Image1.1.1
Image1.1.2
Add 7Y-3966 Terminal As.(assembly of 7Y-3962 Male Terminal & 7Y-3964 Tube) on 568-GN wire and 7Y-3967 Terminal As. (assembly of 7Y-3963 Female Terminal & 7Y-3965 Tube) on H414-YL Wire.
Connect the two terminals and reroute bundle under platform.
Use 3S-2093 Straps to secure bundle on console harness.
Image1.2.1
Image1.2.2
Image1.2.3
Image1.2.4
Insure correct function of warning device.
Position machine with front parts "over the front" in vertical position (fore boom and stick cylinders fully retracted).
Carefully action boom down lever: buzzer should be heard when demolition front parts are positioned such as angle between boom and upper frame is greater than threshold angle. This angle equals 20 degrees on 325D, 25 degrees on 330D, 345C and 365C and 15 degrees on 385C (40m).


Parts elbow Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.