2289355 ELECTRICAL AR Caterpillar parts
CD-54
Rating:
Alternative (cross code) number:
CA2289355
228-9355
2289355
CA2289355
228-9355
2289355
VIBRATORY COMPACTOR,
Compatible equipment models: 2289355:
For full view, you need register
Information:
Installation Procedure
Make sure that the mating surfaces of the travel motor and the travel brake valve are thoroughly clean.
Illustration 1 g00512864Note: Check the condition of O-ring seals (6) and (7). If the O-ring seals are damaged, use new parts for replacement.
Install two large O-ring seals (6) and three small O-ring seals (7) in the travel motor.
Illustration 2 g00512852
Use two people in order to place travel brake valve (5) in position on the travel motor. Install six bolts (4) that secure travel brake valve (5). Tighten the six bolts to a torque of 80 8 N m (60 6 lb ft).
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Remove the plugs from the ends of two tube assemblies (3). Check the condition of the O-ring seals that are used in the ends of two tube assemblies (3). If the O-ring seals are damaged, use new parts for replacement.
Connect two tube assemblies (3) to the travel brake valve in the tube assembly's original locations. Tighten the tube assemblies to a torque of 80 7 N m (59 5 lb ft).
Fill the hydraulic oil tank with hydraulic oil to the correct level. Refer to Operation and Maintenance Manual, "Lubricant Viscosoties" for the proper oil viscosity and Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for the correct filling procedure.
Start the engine and check the travel brake valve for leaks. Also,check the operation of the travel motors. Stop the engine.
Illustration 3 g00486980
Install cover assembly (2). Install the washers and four bolts (1). Tighten four bolts (1) to a torque of 130 10 N m (95 7 lb ft).
Make sure that the mating surfaces of the travel motor and the travel brake valve are thoroughly clean.
Illustration 1 g00512864Note: Check the condition of O-ring seals (6) and (7). If the O-ring seals are damaged, use new parts for replacement.
Install two large O-ring seals (6) and three small O-ring seals (7) in the travel motor.
Illustration 2 g00512852
Use two people in order to place travel brake valve (5) in position on the travel motor. Install six bolts (4) that secure travel brake valve (5). Tighten the six bolts to a torque of 80 8 N m (60 6 lb ft).
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Remove the plugs from the ends of two tube assemblies (3). Check the condition of the O-ring seals that are used in the ends of two tube assemblies (3). If the O-ring seals are damaged, use new parts for replacement.
Connect two tube assemblies (3) to the travel brake valve in the tube assembly's original locations. Tighten the tube assemblies to a torque of 80 7 N m (59 5 lb ft).
Fill the hydraulic oil tank with hydraulic oil to the correct level. Refer to Operation and Maintenance Manual, "Lubricant Viscosoties" for the proper oil viscosity and Operation and Maintenance Manual, "Hydraulic System Oil Level - Check" for the correct filling procedure.
Start the engine and check the travel brake valve for leaks. Also,check the operation of the travel motors. Stop the engine.
Illustration 3 g00486980
Install cover assembly (2). Install the washers and four bolts (1). Tighten four bolts (1) to a torque of 130 10 N m (95 7 lb ft).
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts electrical Caterpillar catalog:
2624117
ELECTRICAL AR
AP-655D
AP-655D
2624128
ELECTRICAL AR
AP-655D
AP-655D
2832492
ELECTRICAL AR
CB-564D
CB-564D
2222586
ELECTRICAL AR
AP-1055D
AP-1055D
2469027
ELECTRICAL AR
PS-360C
PS-360C
2441093
ELECTRICAL AR
AP-655C
AP-655C
3042020
ELECTRICAL AR
CP-44, CS-44
CP-44, CS-44
3212415
ELECTRICAL AR
AP555E, BG500E
AP555E, BG500E
3418685
ELECTRICAL AR
CD-54B
CD-54B
2624121
ELECTRICAL AR
AP-600D, BG600D
AP-600D, BG600D
2931949
ELECTRICAL AR
CB-22
CB-22
3978459
ELECTRICAL AR
CB-34
CB-34