AVSPARE.COM
parts catalog

ELECTRONICS GP-MONITOR 3967456 - Caterpillar



3967456 ELECTRONICS GP-MONITOR Caterpillar parts 770G, 772G ELECTRONICS
Rating:
26
Alternative (cross code) number:
CA3967456
396-7456
3967456
Caterpillar 3967456 ELECTRONICS GP-MONITOR

Buy ELECTRONICS GP-MONITOR 3967456 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK,

Compatible equipment models: 3967456:

TRUCK  770G   772G   Caterpillar
  For full view, you need register

Information:


Electrical shock hazard. The electronic unit injector system uses 90-120 volts.
Remove the valve cover and look for broken parts. Repair any broken parts or replace any broken parts that are found. Inspect all wiring to the solenoids. Look for loose connections. Also look for frayed wires or broken wires. Ensure that the connector for the unit injector solenoid is properly connected. Perform a pull test on each of the wires. Refer to Troubleshooting, "Electrical Connectors - Inspect". Inspect the posts of the solenoid for arcing. If arcing or evidence of arcing is found, remove the cap assembly. Refer to Disassembly and Assembly Manual, "Electronic Unit Injector - Remove". Clean the connecting posts. Reinstall the cap assembly and tighten the solenoid nuts to a torque of 2.5 0.25 N m (22 2 lb in). Refer to Disassembly and Assembly Manual, "Electronic Unit Injector - Install".
Check the valve lash setting for the cylinder of the suspect unit injector. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".
Look for signs of fuel leakage. Investigate the source of the leaking fuel. Remedy the cause of the fuel leak.
Ensure that the bolt that holds the unit injector is tightened to the proper torque. If necessary, loosen the bolt that holds the unit injector and tighten the bolt to a torque of 55 10 N m (40.6 7.4 lb ft).
Remove the suspect unit injector and check the unit injector for signs of exposure to coolant. Refer to Disassembly and Assembly Manual, "Electronic Unit Injector - Remove". Exposure to coolant will cause rust to form on the injector. If the unit injector shows signs of exposure to coolant, remove the injector sleeve and inspect the injector sleeve. Refer to Disassembly and Assembly Manual, "Electronic Unit Injector Sleeve - Remove". Replace the injector sleeve if the injector sleeve is damaged. Check the unit injector for an excessive brown discoloration that extends beyond the injector tip. If excessive discoloration is found, check the quality of the fuel. Refer to Testing and Adjusting, "Fuel Quality - Test". Replace the seals on the injector and reinstall the injector. Refer to Disassembly and Assembly Manual, "Electronic Unit Injector - Install". Also refer to Disassembly and Assembly Manual, "Electronic Unit Injector Sleeve - Install".
If the problem is not resolved, replace the suspect injector with a new injector. In order to verify that the new injector is working properly, perform the Cylinder Cutout Test. Use the Caterpillar Electronic Technician (ET).

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts electronics Caterpillar catalog:

4307772 ELECTRONICS GP-MONITOR
770G, 770G OEM, 772G, 772G OEM
3874549 ELECTRONICS GP-ENGINE
772G, 772G OEM, 834K, 836K, 988K
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.