AVSPARE.COM
parts catalog

ELECTRONICS GP-MONITOR 5088611 - Caterpillar



5088611 ELECTRONICS GP-MONITOR Caterpillar parts ELECTRONICS
Rating:
51
Alternative (cross code) number:
CA5088611
508-8611
5088611
Caterpillar 5088611 ELECTRONICS GP-MONITOR

Buy ELECTRONICS GP-MONITOR 5088611 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 1
 
  For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Lifting Bracket 1
B - Guide Stud
(M10 x 1.25 by 80 mm) 2 Start By:
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03346195
Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb).
Remove two bolts (1) from Positions (X) on the flywheel.
Install Tooling (B) in Positions (X) on the flywheel.
Remove the remaining bolts (1) and remove flywheel (2). Note: On some three cylinder engines, a roll pin is located between the crankshaft and the flywheel.
Inspect ring gear (3) and flywheel (2) for wear or damage. If the ring gear or the flywheel is worn or damaged, use new parts for replacement.
Illustration 2 g00825639
To remove ring gear (3) from flywheel (2), place the flywheel on a suitable support. Use a hammer and a punch (4) in order to remove the ring gear from the flywheel. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Lifting Bracket 1
B - Guide Stud
(M10 x 1.25 by 80 mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been heated.
Illustration 3 g01305341
If the ring gear was removed, follow Steps 1.a through 1.c in order to install ring gear (3) to flywheel (2).
Identify the orientation of the new ring gear in order to install the ring gear correctly onto the flywheel. Note: The chamfered side of Gear Teeth (Y) must face toward the starting motor when the flywheel is installed. The chamfered will ensure the correct engagement of the starting motor.
Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that the orientation of ring gear (3) is correct and quickly install the ring gear onto flywheel (2).
Illustration 4 g03346195
Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If crankshaft rear seal has any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure.
Install Tooling (B) to Positions (X) in the crankshaft.
Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb).
Position flywheel (2) onto Tooling (B). On three cylinder engines that have a roll pin, ensure that the roll pin is installed to the crankshaft and that the roll pin is free from damage. Align the hole in the flywheel with the roll pin in the crankshaft.
Install bolts (1) finger tight.
Remove Tooling (B) and install the two remaining bolts (1).
Use a suitable tool to prevent flywheel (2) from rotating. Tighten bolts (1) to a torque of 74 N m (54 lb ft).
Remove Tooling (A) and

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 Engine
318D2 L Excavator SGB00001-UP (MACHINE) POWERED BY C4.4 Engine
312D2 L Excavator MPP00001-UP (MACHINE) POWERED BY 3054C Engine
318D2 L Excavator XAH00001-UP (MACHINE) POWERED BY 3054C Engine
312F GC Excavator FKE00001-UP (MACHINE) POWERED BY C3.4B Engine
313F LGC Excavator GJD00001-UP (MACHINE) POWERED BY C3.4B Engine
313F LGC Excavator HDK00001-UP (MACHINE) POWERED BY C3.4B Engine
312D2 L Excavator FAB00001-UP (MACHINE) POWERED BY 3054C Engine
320D2 GC Excavator XAK00001-UP (MACHINE) POWERED BY 3054C Engine
320D2 GC Excavator PFE00001-UP (MACHINE) POWERED BY C4.4 Engine


Parts electronics Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.