ELEMENT-FILTER 1887020 - Caterpillar

1887020 ELEMENT-FILTER Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1887020
188-7020
1887020

Weight: 10 pounds 4 kg.

Buy ELEMENT-FILTER 1887020 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Spears 188N Series PVC Pipe Fitting, Nipple, Thread on One End, Schedule 80, Gray, 2" NPT Male x Socket, 2" Length

$10.95

28 Jan 2024

US: A 2 Z AQUATIC S

Spears 188N Series PVC Pipe Fitting, Nipple, Thread on One End, Schedule 80, Gray, 2" NPT Male x Socket, 2" Length
Spears Manufacturing Nipple fitting for connecting threaded and unthreaded pipes || Socket opening on one end and male NPT threads on the other for connecting two pipes with different ends || PVC for chemical and corrosion resistance, high strength, and less weight than fittings made from metal || Maximum operating temperature of 140 degrees F || Meets ASTM D1784 and D2467 standards for quality assurance, and certified by NSF International for potable water service

CAI Approved 2" x 2" PVC Nipple, Pipe Schedule 80, Gray

$14.52

18 May 2021

US: Cold Air Indust

CAI Approved 2" x 2" PVC Nipple, Pipe Schedule 80, Gray
CAI - CAI Approved

Show more prices Caterpillar parts

For full view, you need register

Information:

Remove the bolts that hold the VIMS Guardian ECM to the plate assembly.
Illustration 24 g01545540
(18) E972-BU (19) 195-7970 Pin Remover (20) F419-YL (21) F418-GN
Remove the following three wires from the J connector on the VIMS ECM with a 195-7970 Pin Remover (19) :J2 Pin 66 - E972-BU (18) J2 Pin 41 - F419-YL (20) J2 Pin 40 - F418-GN (21)
Illustration 25 g01423197
Insert the three loose wires from the 299-4675 Wiring Harness into the J connector on the VIMS ECM.
Insert F418-GN into J2 pin 40.
Insert F419-YL into J2 pin 41.
Insert E972-BU into J2 pin 66.
Illustration 26 g01545553
(18) E972-BU (20) F419-YL (21) F418-GN
Insert the three wires that were removed from the VIMS ECM into the open 3-pin DT connector in the 299-4675 Wiring Harness .
Insert E972-BU (18) into pin A.
Insert F419-YL (20) into pin B.
Insert F418-GN (21) into pin C.
Illustration 27 g02229753
Illustration shows the isolators after installation
Use a 194-7583 Plate As in order to remove the 8R-6927 Bosses .
Drill holes in the plate in order to mount the VIMS Communicator in the center of the plate.
Mount the VIMS Communicator to the plate. Use bolts, nuts, and suitable rubber isolator/mounts.
Illustration 28 g01426742
(25) 255-2772 Spacer (26) 101-9759 Spacer (27) 8T-7352 Bolt
Install the following components as one assembly to the tractor: the Guardian ECM, the Guardian hardware, the VIMS Communicator and the plate.
Table 1
Item Part Number Description Quantity
(25) 255-2772 Spacer 2
(26) 101-9759 Spacer 2
(27) 8T-7352 Bolt 4
8T-4224 Hard Washer 4
Suitable isolation mounts (1) 4
( 1 ) Isolators/Mounts should be purchased from outside supplierRefer to Table 1 for the parts that are called out in Illustration 28.
Illustration 29 g01426744
Connect the VIMS Communicator harness at plug (28) and plug (29) .
Connect the two loose wires from the 299-4675 Wiring Harness to a suitable power and ground.Red - 24 V switched powerBlack - Ground
Connect the VIMS Communicator to a radio system with an Ethernet cable.