AVSPARE.COM
parts catalog

ELEMENT OIL 1R0730 - Caterpillar


1R0730 ELEMENT OIL Caterpillar parts
Rating:
19
Alternative (cross code) number:
CA1R0730
1R-0730
1R0730
Caterpillar 1R0730 ELEMENT OIL
Weight: 0.31 pounds 0 kg.

Buy ELEMENT OIL 1R0730 Caterpillar genuine, new aftermarket tractor parts with delivery

Cross Reference:

BALDWIN PT8350, CATERPILLAR 1R0730, 1R0746, 2P5834, DONALDSON P550700, FRAM C1701, LUBERFINER LP4736, WIX FILTERS 51420,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$47.78

06 Oct 2025

CN: dahkejifuwuyoux
1R0730 1R-0730 1R0746 1R-0746 XH453 Return Hydraulic Oil Filter (H-0746)
Generic 1R0730 1R-0730 1R0746 1R-0746 XH453 Return Hydraulic Oil Filter
$37.60

06 Oct 2025

US: YFDREPTOOLS
Replacement For 1R0730 1R0746 2P5834 Filter Fits Caterpillar (Fits CAT)
Amhillras Replacement For 1R0730 1R0746 2P5834 Filter Fits Caterpillar (Fits CAT)
$61.97

06 Oct 2025

US: Zklel
Replacement For Compatible With 1R0746 Element As-Hydraulic Oil Fits Caterpillar 2P5834, 1R0730, PT8350, C8254
FUNBIT
  For full view, you need register

Information:

EUI Engine
The operation of the engine is controlled by the Engine ECM. Some Electronic Unit Injection (EUI) engines utilize a Common Engine Interface (CEI). In CEI applications, the EMCP 4 may send the engine start and the engine stop information across the CAN data link.Note: For a CEI application, the cooldown timer that is in the ECMP 4 should be set to zero.The Engine ECM controls the engine speed and also enables the fuel injection for the engines. The fuel enable input and the speed input can be configured by using the service tool.The fuel enable input to the ECM can be switched to battery negative, or the input can be transmitted over the primary CAN data link.The desired engine speed is derived from one of the two following inputs:
Input from a converter. The converter converts the analog speed signal of a speed potentiometer into a pulse width modulated signal for delivery over the primary CAN data link.
The ECM uses feedback from the engine speed sensors that are mounted on the engine to control the engine speedThere are primary and secondary throttle inputs. The throttle inputs can be a pulse width modulated signal or the speed inputs can be transmitted over the primary CAN data link.Note: Caterpillar Electronic Technician (Cat ET) is used to configure the throttle inputs as either primary or as secondary.The Engine ECM will acknowledge the failure, generate a diagnostic, and respond to the secondary input if the primary throttle input fails. The engine will default to the idle speed setting if the primary throttle input fails and the secondary input is disabled.The EMCP 4 receives specific information that is used in order to monitor the system for events.Note: The EMCP 4 does not display the parameter name for unsupported parameters.The following information is shown on the display screen of the EMCP 4 if the information is supported by the Engine ECM:
Engine Oil Pressure
Engine Coolant Temperature
Left Exhaust Manifold Temperature
Right Exhaust Manifold Temperature
Intake Manifold Temperature
Oil Temperature
Fuel Pressure
Boost Pressure
Oil Filter Differential Pressure
Fuel Filter Differential Pressure
Air Filter Differential Pressure
Engine Fuel Temperature
Battery Voltage
Engine Speed (rpm)
Engine Hours
Engine State
Service (hrs)/days
Total Crank (Cranks)
Total Start (Starts)
Exhaust Temp
Turbo 1, 2, 3, and 4 Compressor Inlet Temp
Turbine 1, 2, 3, and 4 Inlet Temp
Turbine 1, 2, 3, and 4 Outlet Temp
Cylinder Temps
Crankcase Pressure
Total Fuel
Rate of Fuel Note: Only the values that are supported by other modules, and that are broadcast on one of the CAN data links will be displayed.The EMCP 4 displays the diagnostic trouble codes from the ECM as a convenience to the operator.Reference: For information on the management of diagnostic trouble codes by the EMCP 4 and the ECM, refer to Troubleshooting, "Diagnostic Trouble Code List". Reference: For EMCP 4 settings that are specific to EUI engine applications, refer to the setpoint tables in Testing and Adjusting, "Electronic Control Module (Generator Set) - Configure".


Parts element Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.