ELEMENT A 3M0198 - Caterpillar

3M0198 ELEMENT A Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA3M0198
3M-0198
3M0198

Weight: 0.70 pounds 0 kg.

Buy ELEMENT A 3M0198 Caterpillar genuine, new aftermarket tractor parts with delivery

Cross Reference:

ACDelco 12-334, PF 334, ALCO FILTER MD-025, ASAS AS 24 H, BALDWIN PT88, PT88-HD, CARELLO 47.040.000, CATERPILLAR 1R-0720, 1R-0721, 1W-7000, 2M-9140, 2Y-8099, 3M-0198, 3M-318, 4R-485, 4S-485, 5H-6886, 5L-8363, 5S-0485, 5S-485, 6H-9936, 6H-9937, 6H-9999, 8F-1151, 8M-6018, P5S-485, CHAMP LP 163, CLEAN FILTERS ML 402, COOPERS AZL 061, G 551, G 552, COOPERSFIAAM FILTERS FA4005, FA4592, CROSLAND 1021, 490, DONALDSON P550485, P779017, DONIT FILTER 49.10.141, ELOFIC EXL-667, FIAT 759951, FIATALLIS FIL FILTER ML 141, FLEETGUARD LF519, LF729, FORD 5000 842, A 730 X 6744 D2A, FRAD 42.58.01/40, FRAM C1656APL, CH238PL, GENERAL MOTORS 5574589, 5575245, 5576073, 6438401, 6438409, GUD FILTERS G 551, HENGST FILTER E229.86H, E52H D115, HYSTER 75658, 75669, 8297372, KOMATSU 5S485, 600-211-1210, 612-050-5101, 612-751-5040, LUBERFINER LFH 1560, LP 163, MAHLE FILTER OX 2, OX 217D, MASSEY FERGUSON 1810404M91, 1810950M91, 182781M1, 1 851 399, 1 852 781, 812 073, MISFAT L400, MOTORCRAFT EFL 204, P.B.R. AC-1060, PUROLATOR MF 292 A/1, PR 40, R 7, RYCO HDR2072P, HDR2072PA, SCT Germany SH 4719, SOFIMA S 8320 PO, TECNOCAR OP238, TEHO 5112, D 112, TJ FILTERS FP 9484, UFI 25.400.00, UNICO FILTER LE 13229, VAG 140 523 250, M40523250, WIX FILTERS 51168, WOODGATE WGH 6093, WGH 9098,

Show more prices Caterpillar parts

For full view, you need register

Information:

(1) Torque for three long studs in cylinder block ... 27 4 N m (20 3 lb ft) Put 9S3263 Thread Lock on threads of short stud in front housing.(2) Oil seal. Put clean engine oil on the seal lip. Assemble with the lip toward the bearings.(3) Seal. Put a thin layer of clean engine oil in the bore for the seal.(4) Ring and water seal. Use a 7N7843 Seal Installation Tool and hand pressure to install the rubber seal and ceramic ring as a unit in the pump housing bore. Make sure the identification mark (holes or groove) on the ceramic ring face is installed inside the rubber seal.(5) Seal assembly. a. Remove the spring from the seal.b. Put clean water on the seal assembly as the only lubrication for assembly. Do not get any grease or oil on the seal faces.c. Do not stretch the rubber of the seal assembly at installation. If the seal is stretched, the service life is shortened.d. Use a 7N7843 Seal Installation Tool and hand pressure to install the seal assembly on the pump shaft until the carbon face makes light contact with the smooth face of the ceramic ring. The carbon seal assembly must rotate with the water pump shaft. Do not use any lubricant (except clean water) that will reduce the friction between the seal and the shaft.e. Install the carbon seal assembly spring.(6) Shaft diameter at carbon seal assembly seat area must be ... 19.10 0.05 mm (.752 .002 in) Use 4C9500 Quick Cure Primer to clean the water pump shaft and the ceramic ring seal counterbore in the pump housing.(7) Torque for the bolt that holds the impeller ... 39 3 N m (28 2 lb ft)(8) Clearance between impeller and housing ... 0.56 to 1.50 mm (.022 to .059 in)