4I7575 ELEMENT AS Caterpillar parts
311, 315, 910E, 914G, IT12B, IT14G
Rating:
Alternative (cross code) number:
CA4I7575
4I-7575
4I7575
CA4I7575
4I-7575
4I7575
Weight: 4 pounds 2 kg.
Information:
EFFECTIVE FILTER AREA
4.16
mm2
LENGTH
394
mm
MAJOR OD
235
mm
MINOR OD
187.6
mm
TYPE
000000000004
COMPACT WHEEL LOADER, INTEGRATED TOOLCARRIER,
Cross Reference:
AMC Filter
HA-1961,
BALDWIN
PA2788,
CASE IH
161863A1,
CATERPILLAR
096-4175,
4I-7575,
DONALDSON
R800103,
FIL FILTER
HP 4085,
FLEETGUARD
AF4567,
HENGST FILTER
E745L,
HITACHI
4129905,
4129907,
JCB
KRH0787,
KOMATSU
600-181-6540,
600-181-6550,
LUBERFINER
LAF 1804,
MISFAT
RM885,
MITSUBISHI
3423000800,
WIX FILTERS
46600,
WOODGATE
WGA460,
You can buy:
US$85.99
15 Jul 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
(Set of 1) Veyronix 4I-7575 6I6582 PA2788 PA1911 Engine Air Filte KIT Compatible With Caterpillar 910E 910F 914G Wheel-Type Loader/312-A 311-A 315-A 315-A L Excavator Replaces A462C P106834 C19457
Veyronix Cross referencing OE: 4I7575 4I-7575 6I-6582 6I6582 PA2788 PA1911 A462C P106834 P109374 P110557 122-4550 6I-6582 42543 42924 227671 AR45943 AR46004 C1281 9912-45800 6001823400 2451U3113 161863A1 3I1426 3909821 204632 2446U144S2 227457 80227671 813957 3I0127 AR47100 6001816050 7475191 || Application Model:Compatible With Caterpillar 910E 910F 914G Wheel-Type Loader/312-A 311-A 315-A 315-A L Excavator/IT12B IT14F IT14G Integrated Toolcarrier || Application Model:Compatible With KOMATSU D31 D37 D41 Bulldozer/PC100-6 120-6 120LC-6 128UU-1 130-6 150-5 200-5 220 220LC-5 Crawler Excavator/ WA100-3A 120-2 120-3 Wheel Skid Steer Loader || Manufactured to OEM standards and rigorously tested at the factory || Package Includes: 1 x Inner Filter 6I6582; 1 x Outter Filter 4I7575
Veyronix Cross referencing OE: 4I7575 4I-7575 6I-6582 6I6582 PA2788 PA1911 A462C P106834 P109374 P110557 122-4550 6I-6582 42543 42924 227671 AR45943 AR46004 C1281 9912-45800 6001823400 2451U3113 161863A1 3I1426 3909821 204632 2446U144S2 227457 80227671 813957 3I0127 AR47100 6001816050 7475191 || Application Model:Compatible With Caterpillar 910E 910F 914G Wheel-Type Loader/312-A 311-A 315-A 315-A L Excavator/IT12B IT14F IT14G Integrated Toolcarrier || Application Model:Compatible With KOMATSU D31 D37 D41 Bulldozer/PC100-6 120-6 120LC-6 128UU-1 130-6 150-5 200-5 220 220LC-5 Crawler Excavator/ WA100-3A 120-2 120-3 Wheel Skid Steer Loader || Manufactured to OEM standards and rigorously tested at the factory || Package Includes: 1 x Inner Filter 6I6582; 1 x Outter Filter 4I7575
4I7575 for Element A/Primary Fits Caterpillar IT12B IT14G 914G
Generic Package included: 1x 4I7575 for Element A / Primary Fits Caterpillar IT12B IT14G 914G as the picture . || High-Performance Efficiency: gineered for maximum efficiency, this product delivers exceptional performance without compromising on quality. It’s a versatile replacement suitable for various applications. || Identify the model: USE Ctrl + F to SEARCH your model number inside the Product Description. || Note: If you are not sure about the compatibility please contact us for advice. we will solve your problem within 24 hours || Note: If you are not sure about the compatibility please contact us for advice. we will solve your problem within 24 hours
Generic Package included: 1x 4I7575 for Element A / Primary Fits Caterpillar IT12B IT14G 914G as the picture . || High-Performance Efficiency: gineered for maximum efficiency, this product delivers exceptional performance without compromising on quality. It’s a versatile replacement suitable for various applications. || Identify the model: USE Ctrl + F to SEARCH your model number inside the Product Description. || Note: If you are not sure about the compatibility please contact us for advice. we will solve your problem within 24 hours || Note: If you are not sure about the compatibility please contact us for advice. we will solve your problem within 24 hours
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 4I7575:
Information:
Note: If the symptom is intermittent and the symptom cannot be repeated, refer to Troubleshooting, "Intermittent Low Power or Power Cutout". If the symptom is consistent and the symptom can be repeated, continue with this procedure.Probable Causes
Diagnostic codes
Programmable parameters
Electrical connectors
Cold mode
Fuel injectors
Fuel supply
Air inlet and exhaust systemRecommended Actions
Note: If the symptom only occurs under certain operating conditions (high idle, full load, engine operating temperature, etc), test the engine under those conditions. Troubleshooting the symptom under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps Values Results
1. Check for Active Diagnostic Codes
Codes
Result: There are no active diagnostic codes.
Proceed to Test Step 2.
Result: There are active diagnostic codes.
Repair: Troubleshoot any active codes before continuing with this procedure.
If the problem is not resolved, proceed to Test Step 2.
2. Check the Programmable Parameters
A. Check the following parameters on Cat ™ ET:
• Throttle Position Sensor
Programmable Parameters
Result: The programmable parameters are correct.
Proceed to Test Step 2.
Result: The programmable parameters are incorrect.
Repair: Determine the type of throttle that is used in the application. Program the parameters to match the type of throttle that is used. Refer to Troubleshooting, "Throttle Position Sensor Circuit - Test" for more information.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Electrical Connectors
A. Check the connectors for the Electronic Control Module (ECM) and the connectors for the unit injectors for correct installation. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Electrical Connectors
Result: The electrical connectors are OK.
Proceed to Test Step 4.
Result: The electrical connectors are worn or damaged.
Repair: Repair or replace the electrical connectors.
If the problem is not resolved, proceed to Test Step 4.
4. Check for Cold Mode Operation
A. Use Cat™ ET to verify that the engine has exited cold mode. Cold mode operation may cause the engine to run rough and the engine power may be limited.
Cold Mode
Result: The engine is not in cold mode.
Proceed to Test Step 5.
Result: The engine is in cold mode.
Repair: Take the engine out of cold mode.
If the problem is not resolved, proceed to Test Step 5.
5. Check the Fuel Injectors
A. Use Cat ET to determine if there are any active diagnostic codes for the unit injectors.
B. Perform the injector solenoid test on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM. Refer to Troubleshooting, "Injector Solenoid Circuit - Test" for the proper procedure.
C. Perform the cylinder cutout test on Cat ET in order to identify any injectors that might be misfiring. Refer to Troubleshooting, "Injector Solenoid Circuit - Test" for the proper procedure.
Fuel Injectors
Result: The fuel injectors are OK.
Proceed to Test Step 5.
Result: The fuel injectors are NOT OK.
Repair: Replace the fuel injectors.
If the problem is not resolved, proceed to Test Step 6.
6. Check the Fuel Supply
A. Check the fuel lines for the following problems: restrictions, collapsed lines, and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
B. Check the fuel tank for foreign objects which may block the fuel supply.
Prime the fuel system if
Diagnostic codes
Programmable parameters
Electrical connectors
Cold mode
Fuel injectors
Fuel supply
Air inlet and exhaust systemRecommended Actions
Note: If the symptom only occurs under certain operating conditions (high idle, full load, engine operating temperature, etc), test the engine under those conditions. Troubleshooting the symptom under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps Values Results
1. Check for Active Diagnostic Codes
Codes
Result: There are no active diagnostic codes.
Proceed to Test Step 2.
Result: There are active diagnostic codes.
Repair: Troubleshoot any active codes before continuing with this procedure.
If the problem is not resolved, proceed to Test Step 2.
2. Check the Programmable Parameters
A. Check the following parameters on Cat ™ ET:
• Throttle Position Sensor
Programmable Parameters
Result: The programmable parameters are correct.
Proceed to Test Step 2.
Result: The programmable parameters are incorrect.
Repair: Determine the type of throttle that is used in the application. Program the parameters to match the type of throttle that is used. Refer to Troubleshooting, "Throttle Position Sensor Circuit - Test" for more information.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Electrical Connectors
A. Check the connectors for the Electronic Control Module (ECM) and the connectors for the unit injectors for correct installation. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Electrical Connectors
Result: The electrical connectors are OK.
Proceed to Test Step 4.
Result: The electrical connectors are worn or damaged.
Repair: Repair or replace the electrical connectors.
If the problem is not resolved, proceed to Test Step 4.
4. Check for Cold Mode Operation
A. Use Cat™ ET to verify that the engine has exited cold mode. Cold mode operation may cause the engine to run rough and the engine power may be limited.
Cold Mode
Result: The engine is not in cold mode.
Proceed to Test Step 5.
Result: The engine is in cold mode.
Repair: Take the engine out of cold mode.
If the problem is not resolved, proceed to Test Step 5.
5. Check the Fuel Injectors
A. Use Cat ET to determine if there are any active diagnostic codes for the unit injectors.
B. Perform the injector solenoid test on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM. Refer to Troubleshooting, "Injector Solenoid Circuit - Test" for the proper procedure.
C. Perform the cylinder cutout test on Cat ET in order to identify any injectors that might be misfiring. Refer to Troubleshooting, "Injector Solenoid Circuit - Test" for the proper procedure.
Fuel Injectors
Result: The fuel injectors are OK.
Proceed to Test Step 5.
Result: The fuel injectors are NOT OK.
Repair: Replace the fuel injectors.
If the problem is not resolved, proceed to Test Step 6.
6. Check the Fuel Supply
A. Check the fuel lines for the following problems: restrictions, collapsed lines, and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
B. Check the fuel tank for foreign objects which may block the fuel supply.
Prime the fuel system if
Caterpillar parts catalog:
Parts element Caterpillar catalog:
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 16G, 16H NA, 205B, 214B, 215, 215B, 224B, 235, 235B, 245, 3114, 311...
120G, 120H, 120H ES, 120H NA, 12E, 12F, 12G, 12H, 12H NA, 130G, 135H, 135H NA, 140B, 140G, 14E, 14G, 16, 160G, 1673, 1693, 16G, 215, 215B, 225, 225D, 231D, 235, 235B, 235C, 245, 24H, 3176B, 3204, 3304...
120H, 120H NA, 135H, 135H NA, 3114, 3116, 3126, 3126B, 3126E, 324D FM, 324D FM LL, 324D L, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D L, 35, 45, 55, 561M, 561N, 924F, 928G, 938F, 938G,...
120H, 120H ES, 135H, 3114, 3116, 3126, 3126B, 3208, 324D, 326D L, 329D, 35, 45, 561M, 561N, 918F, 924F, 928G, 938F, 938G, 938G II, 950F II, 950G, 950G II, 950H, 953C, 960F, 962G, 962G II, 962H, 963B, ...
1278604
ELEMENT AS-JACKET WATER HEATER
908, 914G, IT14G, TH350B, TH355B, TH460B
908, 914G, IT14G, TH350B, TH355B, TH460B
1278606
ELEMENT AS-JACKET WATER HEATER
908, 914G, IT14G, TH350B, TH355B, TH460B
908, 914G, IT14G, TH350B, TH355B, TH460B
416, 428, 446, 578, D10N, D5H, D5HTSK II, D6H, D6H XL, D6H XR, D6M, D6R, D7H, D8N, D8R, D9N, D9R, IT12B
515, 525, 950B, 950F, 950F II, 960F, IT12B, IT14B, R1300, R1300G, RT100
3T8723
ELEMENT AS-JACKET WATER HEATER
3208, 916, 938F, 950F II, 960F, 963B, IT12B, IT28F
3208, 916, 938F, 950F II, 960F, 963B, IT12B, IT28F
308E, 308E CR, 308E SR, 311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 315C, 315D L, 316E L, 317B LN, 318B, 31...
311, 315, 910E, IT12B
311
1371004
ELEMENT ASSEM.
307B, 311B, 325B, 330B, 345B L, 365B, 365B L, 365C, 365C L, 375, 385B, 385C, 385C FS, 385C L, 5080
307B, 311B, 325B, 330B, 345B L, 365B, 365B L, 365C, 365C L, 375, 385B, 385C, 385C FS, 385C L, 5080
307, CB-534B
225
120G, 215, 215B, 930, 943, D4E, IT28
245, 583K, 621B, 621R, 627B, 777, 824C, 826C, 963, 973, 980B, 980C, 980F, 992, D10, D250B, D25C, D300B, D30C, D350C, D35C, D35HP, D400, D6C, D6D, D8H, D8K
1624960
ELEMENT
307
307
307, E70, E70B
0952124
ELEMENT
307, E70, E70B
307, E70, E70B
0963384
ELEMENT
307, E110, E70, E70B
307, E110, E70, E70B
311
311, 315, 910E, IT12B