AVSPARE.COM
parts catalog

END 2H9477 - Caterpillar



2H9477 END Caterpillar parts D9E END
Rating:
78
Alternative (cross code) number:
CA2H9477
2H-9477
2H9477
Caterpillar 2H9477 END
Weight: 0.80 pounds 0 kg.

Buy END 2H9477 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 2H9477:

TRACK-TYPE TRACTOR  D9E   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:


Illustration 2 g03324436
Right side view
Table 2
Item     Qty     Part     Specification Description    
7     4     5F-9657 O-Ring Seal     Lubricate the bore lightly with 5P-3975 Rubber Lubricant.    
G     3     7N-2047 Dowel     Extension of the dowel from the front face of the cylinder block is
6.0 0.5 mm (0.24 0.02 inch).    
H     2     4N-0683 Dowel     Extension of dowels from the rear face of the cylinder block is
19.0 0.5 mm (0.75 0.02 inch).    
J     2     7N-2044 Dowel     Extension of dowels from the front face of the cylinder block is
40.0 0.5 mm (1.57 0.02 inch).    
Illustration 3 g03324437
Table 3
Item     Qty     Part     Specification Description    
8     16     352-6061 Liner Seal     Assemble liner seals dry on clean and dry liner grooves.
Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap.    
9     48     7N-2046 O-Ring Seal     Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap.    
10     9     223-1696 Crankshaft Bearing Cap     Width of the crankshaft bearing cap is
340.030 0.015 mm (13.3870 0.0006 inch).    
11     36     7X-7925 Bolt     Use the following procedure in order to tighten the crankshaft bearing cap bolts:
Install main bearing caps with the cast part number and FRONT toward the front of the block. Each cap has a number. Each cap must be installed in the same position as the correct number on the side of the cylinder block pan rail.
1. Before assembly, lubricate the threads completely with clean engine oil.
2. Hand tighten bolts in the tapped holes.
3. Tighten bolts in the numerical sequence as shown in Illustration 3 to
190 14 N m (140 10 lb ft).
4. Again, tighten each bolt to an additional angle of 180 5 degrees.    
K     -     -     Width in the cylinder block for crankshaft bearing cap is
339.985 0.015 mm (13.3852 0.0006 inch).    
L     -     -     New dimension from centerline of crankshaft bearing bore to the top of the block is
586.00 mm (23.071 inch).    

Caterpillar parts catalog:

Caterpillar parts catalog
D9 TRACTOR 50A00001-00212 (MACHINE)


Parts end Caterpillar catalog:

1A9252 END-ADJUSTMENT ROD
12E, 14E, 16, 163, 173B, 191, 235, 235C, 235D, 245, 245B, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 508, 517, 5230, 5230B, 527, 561B, 561C, 561D, 561H, 571G, 572G, 583H, 583K, 589, 5...
5B2279 END
120, 120B, 120G, 12E, 12G, 130G, 140, 140B, 140G, 14E, 14G, 160G, 16G, 46, 955C, D315, D342, D342C, D8H, D9E
906A END
12E, 14E, 561B, 583H, 594, 955C, 977H, 977K, D6C, D8H, D9E, D9G
5H4847 END
D5, D7F, D8H, D9E, D9G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.