3G8322 END BIT (L.H.) Caterpillar parts
5S, D5B
Rating:
Alternative (cross code) number:
CA3G8322
3G-8322
3G8322
CA3G8322
3G-8322
3G8322
Weight: 33 pounds 14 kg.
BULLDOZER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 3G8322 General Duty End Bit for Model D4/D4 LGP/D5/D5 LGP Bulldozers & Compactors, Left Hand, Straight Blade Model, 0.88" Thickness
CTP For Model D4/D4 LGP/D5/D5 LGP Bulldozers & Compactors || Left Hand || Straight Blade Model || 0.88" Thickness
CTP For Model D4/D4 LGP/D5/D5 LGP Bulldozers & Compactors || Left Hand || Straight Blade Model || 0.88" Thickness
Replacement End Bit - Hot Cupped fits Caterpillar 3G8322 New
Generic
Generic
Number on catalog scheme:
16
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 309-2793 Load Leveler Gp 1
B - Loctite™Quickstix 534–HI-Tack Gasket Sealant -
C - Loctite™RTV Clear Silicone -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Inspect all O-rings, seals, and gaskets for wear and damage. Replace if necessary.
Ensure that the mating surfaces of the engine block, flywheel housing, front drive housing, and oil pan are clean. All mating surfaces must be clean, dry, and free of any oil before Tooling is applied.Note: The oil pan and oil pan gasket must be assembled to the block within 10 minutes of RTV application.Note: Read steps 1 - 4 before beginning sealant application.
Illustration 1 g06226165
Example of a puzzle joint.
Apply Tooling (B) between the gasket and the oil pan to hold the gasket in place during assembly. Do Not apply sealant at eight puzzle joints (Y) or T-joints (W) and (X).
Apply Tooling (C) to all T-joint locations (W) and (X). The bead should cover the entire span of the T-joint and have a constant cross section of 3 – 5 mm (.12 - .20 in).
Illustration 2 g06226746
Offset to housing side.
Illustration 3 g06226743
Offset to block side.
If, there is an offset at the gasket (14) between the block (15) and either housing (16) apply Tooling (C) to the lower side of the misaligned parts. Sealant shall have a cross section height of 3 – 5 mm (.12 -.20 in) and be placed perpendicular to the existing T-jont bead. The new bead shall extend no further than distance (V), 12 mm (0.47 inch) before the next bolt hole location. The existing bead is not shown in the above images to illustrate misalignment.
Illustration 4 g06225737
Use Tooling (A) to position the engine (12) onto the engine oil pan (13). The engine weighs approximately 8555 kg (18860.5lb).
Illustration 5 g06225104
Loosely install 50 bolts (11) on the sides of the oil pan.
Illustration 6 g06224654
Parts made transparent for clarity.
Loosely install nine bolts (9) behind the flywheel housing (10).
Illustration 7 g06224630
Loosely install nine bolts (7) under the damper assembly (8) in the front of the engine.
Tighten the end bolts followed by the left and right side bolts. Start with a bolt toward the center of the right and left side of the pan and work towards the ends.
Retighten the three center bolts on the left and right sides.
Retighten all end bolts.
Illustration 8 g06224600
Install two bolts (5) into the prelubrication pump flange (6).
Illustration 9 g06224579
Install two bolts (3) into the oil pump flange (4).
Illustration 10 g06224530
Install four bolts (2) into the fuel lines support bracket (1).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 309-2793 Load Leveler Gp 1
B - Loctite™Quickstix 534–HI-Tack Gasket Sealant -
C - Loctite™RTV Clear Silicone -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Inspect all O-rings, seals, and gaskets for wear and damage. Replace if necessary.
Ensure that the mating surfaces of the engine block, flywheel housing, front drive housing, and oil pan are clean. All mating surfaces must be clean, dry, and free of any oil before Tooling is applied.Note: The oil pan and oil pan gasket must be assembled to the block within 10 minutes of RTV application.Note: Read steps 1 - 4 before beginning sealant application.
Illustration 1 g06226165
Example of a puzzle joint.
Apply Tooling (B) between the gasket and the oil pan to hold the gasket in place during assembly. Do Not apply sealant at eight puzzle joints (Y) or T-joints (W) and (X).
Apply Tooling (C) to all T-joint locations (W) and (X). The bead should cover the entire span of the T-joint and have a constant cross section of 3 – 5 mm (.12 - .20 in).
Illustration 2 g06226746
Offset to housing side.
Illustration 3 g06226743
Offset to block side.
If, there is an offset at the gasket (14) between the block (15) and either housing (16) apply Tooling (C) to the lower side of the misaligned parts. Sealant shall have a cross section height of 3 – 5 mm (.12 -.20 in) and be placed perpendicular to the existing T-jont bead. The new bead shall extend no further than distance (V), 12 mm (0.47 inch) before the next bolt hole location. The existing bead is not shown in the above images to illustrate misalignment.
Illustration 4 g06225737
Use Tooling (A) to position the engine (12) onto the engine oil pan (13). The engine weighs approximately 8555 kg (18860.5lb).
Illustration 5 g06225104
Loosely install 50 bolts (11) on the sides of the oil pan.
Illustration 6 g06224654
Parts made transparent for clarity.
Loosely install nine bolts (9) behind the flywheel housing (10).
Illustration 7 g06224630
Loosely install nine bolts (7) under the damper assembly (8) in the front of the engine.
Tighten the end bolts followed by the left and right side bolts. Start with a bolt toward the center of the right and left side of the pan and work towards the ends.
Retighten the three center bolts on the left and right sides.
Retighten all end bolts.
Illustration 8 g06224600
Install two bolts (5) into the prelubrication pump flange (6).
Illustration 9 g06224579
Install two bolts (3) into the oil pump flange (4).
Illustration 10 g06224530
Install four bolts (2) into the fuel lines support bracket (1).
Caterpillar parts catalog:
Parts end Caterpillar catalog:
12E, 14E, 16, 163, 173B, 191, 235, 235C, 235D, 245, 245B, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 508, 517, 5230, 5230B, 527, 561B, 561C, 561D, 561H, 571G, 572G, 583H, 583K, 589, 5...
120G, 12E, 12G, 130G, 140, 140G, 141, 14G, 153, 16, 160G, 163, 16G, 191, 215, 215B, 215C, 215D, 518, 518C, 528, 528B, 530B, 561C, 561D, 571G, 572G, 583H, 583K, 666, 904H, 943, 950, 951B, 953C, 955H, 9...
120G, 130G, 140G, 191, 528, 561D, 571G, 594H, 611, 615C, 815, 824B, 825B, 834, 920, 930, 931B, 941, 943, 950, 951B, 953, 953B, 953C, 955C, 955H, 955K, 955L, 963, 966C, 966R, 973, 977D, 977H, 977K, 977...
4S, 5S, 6A, D4E, D5B
4S, 5S, 6A, D4E, D5B
9F7076
END BIT (L.H.)
5S, 6A, 977D
5S, 6A, 977D
5S, 6A, D5B
5S, 6A, D5B
5P0122
END
561C, D5, D5B
561C, D5, D5B
5S, D5B
5J6937
END BIT (RH)
5S, 6A, 814S
5S, 6A, 814S
5J6938
END BIT (LH)
5S, 6A, 814S
5S, 6A, 814S
824, 824B, 826B, 834, 977L, 988, 992
7K8446
END
515, 525, 525B, 535B, 545, 955L, 988B, 992D
515, 525, 525B, 535B, 545, 955L, 988B, 992D
9K8785
END
153
153
1P9500
END
528, 528B, 530B, 611, 613B, 613C, 613C II, 615, 615C, 768B, 769, 772, 773, 936, 936F, 955L, G936
528, 528B, 530B, 611, 613B, 613C, 613C II, 615, 615C, 768B, 769, 772, 773, 936, 936F, 955L, G936
2K4277
END
191, 508, 955C, 955H, 955L
191, 508, 955C, 955H, 955L
8J8956
END BIT
9A, 9S
9A, 9S
2K2294
END
572G, 583K
572G, 583K
5J6938
END BIT (LH)
5S, 6A, 814S
5S, 6A, 814S
5J6937
END BIT (RH)
5S, 6A, 814S
5S, 6A, 814S
5S, D5B