1304803 ENGINE AR-PRIMARY Caterpillar parts
PS-150B
Rating:
Alternative (cross code) number:
CA1304803
130-4803
1304803
CA1304803
130-4803
1304803
Weight: 810 pounds 367 kg.
PNEUMATIC COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Buyers Products 1304803 Cutting Edge 108Inx 6.0In X .500
Buyers Products Company Similar to Curtis OEM# 1TBP49C || References to manufacturers or brands are for descriptive purposes only.
Buyers Products Company Similar to Curtis OEM# 1TBP49C || References to manufacturers or brands are for descriptive purposes only.
RAParts 1304803 -Cutting Edge 1/2 X 6 X 108 INCH - HIGH Carbon Steel-NO Curtis OEM#
Reliable Aftermarket Parts Our Name Says It All OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
Reliable Aftermarket Parts Our Name Says It All OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
For full view, you need register
Compatible equipment models: 1304803:
Information:
This procedure is for later 7000 Series Fuel Injection Nozzles with 40.45 mm (1.593 in.) adapter bores.START BY:a. remove valve covers
Typical Example1. Use tool (A), and disconnect fuel line (1) at both ends. Remove the fuel line from the engine.2. Use tool (B), and remove retainer (2) from the adapter.3. Remove the fuel injection nozzles with tooling (C) as follows:a. Install the 6V6983 Adapter and the 8T3199 Screw into nozzle assembly (3).b. The 8T3198 Tube over the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw to pull the fuel injection nozzle from the adapter.4. Remove compression seal (4) and carbon dam seal (8) from fuel injection nozzle (3).5. Use tool (D), and remove adapter (6) from the cylinder head.6. Remove gasket (7) and seal (5) from adapter (6). The following steps are for installation of the fuel injection nozzles and adapters.7. Use tool (E) to clean the bore in adapter (6). Use an open end wrench or tap driver to turn tool (E).8. Inspect seal (5) for damage or wear. Replace the seal if necessary.9. Put washer (7) and seal (5) in position on adapter (6).10. Put liquid soap in the bores of the cylinder head and in seals (5) in the adapters.11. Put 5P3931 Anti-Seize Compound on the threads of adapter (6), and install the adapter in the cylinder head assembly.12. Use tool (D), and tighten the adapter to a torque of 205 14 N m (150 10 lb.ft.).
Make sure the correct compression seal washer (4) is used when the nozzle assembly is installed in the adapter. Only copper washers are to be used with this adapter.
13. Install compression seal washer (4), and use tool (F) to install carbon dam seal (8) on the fuel injection nozzle.14. Put fuel injection nozzle (3) in position in the adapter, and install retainer (2).15. Use tool (B) to tighten retainer (2) to a torque of 48 7 N m (35 5 lb.ft.).16. Install fuel line (1). Tighten the nuts on the fuel line with tool (A) to a torque of 40 7 N m (30 5 lb.ft.).END BY:a. install valve covers
Typical Example1. Use tool (A), and disconnect fuel line (1) at both ends. Remove the fuel line from the engine.2. Use tool (B), and remove retainer (2) from the adapter.3. Remove the fuel injection nozzles with tooling (C) as follows:a. Install the 6V6983 Adapter and the 8T3199 Screw into nozzle assembly (3).b. The 8T3198 Tube over the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw to pull the fuel injection nozzle from the adapter.4. Remove compression seal (4) and carbon dam seal (8) from fuel injection nozzle (3).5. Use tool (D), and remove adapter (6) from the cylinder head.6. Remove gasket (7) and seal (5) from adapter (6). The following steps are for installation of the fuel injection nozzles and adapters.7. Use tool (E) to clean the bore in adapter (6). Use an open end wrench or tap driver to turn tool (E).8. Inspect seal (5) for damage or wear. Replace the seal if necessary.9. Put washer (7) and seal (5) in position on adapter (6).10. Put liquid soap in the bores of the cylinder head and in seals (5) in the adapters.11. Put 5P3931 Anti-Seize Compound on the threads of adapter (6), and install the adapter in the cylinder head assembly.12. Use tool (D), and tighten the adapter to a torque of 205 14 N m (150 10 lb.ft.).
Make sure the correct compression seal washer (4) is used when the nozzle assembly is installed in the adapter. Only copper washers are to be used with this adapter.
13. Install compression seal washer (4), and use tool (F) to install carbon dam seal (8) on the fuel injection nozzle.14. Put fuel injection nozzle (3) in position in the adapter, and install retainer (2).15. Use tool (B) to tighten retainer (2) to a torque of 48 7 N m (35 5 lb.ft.).16. Install fuel line (1). Tighten the nuts on the fuel line with tool (A) to a torque of 40 7 N m (30 5 lb.ft.).END BY:a. install valve covers
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts engine Caterpillar catalog:
1206832
ENGINE AR
PS-150B
PS-150B
2266469
ENGINE AR-PRIMARY
PS-150B
PS-150B
2266465
ENGINE AR-PRIMARY
BG-225C
BG-225C
1416641
ENGINE AR
BG-225C
BG-225C
1152299
ENGINE AR
BG-225C
BG-225C
1789390
ENGINE AR
BG-245C
BG-245C
1054766
ENGINE AR
BG-2455C, BG-245C
BG-2455C, BG-245C
1304802
ENGINE AR-PRIMARY
CS-323C
CS-323C
3026256
ENGINE AR-PRIMARY
CB-534D, CB-564D
CB-534D, CB-564D
2974048
ENGINE AR-PRIMARY
CB-534D, CB-564D
CB-534D, CB-564D
1568491
ENGINE AR-PRIMARY
CB-214D
CB-214D
1790479
ENGINE AR-PRIMARY
CB-534B
CB-534B
1158327
ENGINE AR
AP-1000B
AP-1000B
2266469
ENGINE AR-PRIMARY
PS-150B
PS-150B