1350880 ENGINE AR-COMPLETE Caterpillar parts
3126
Rating:
Alternative (cross code) number:
CA1350880
135-0880
1350880
CA1350880
135-0880
1350880
TRUCK ENGINE,
Related part:
1350880
SHORT BLOCK
0R8936
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$40.69
30 Jul 2020
2.95[0.90] Pounds
-: -
Exmark 135-0880 Exhaust Plate Lazer Z Diesel
Genuine Exmark Toro Factory Part Number 135-0880 || Compatible with Lazer Z Diesel || This Genuine Exmark product includes a full OEM Warranty.
Genuine Exmark Toro Factory Part Number 135-0880 || Compatible with Lazer Z Diesel || This Genuine Exmark product includes a full OEM Warranty.
For full view, you need register
Compatible equipment models: 1350880:
Information:
Introduction
This procedure provides a method to determine if the steering relief valve is set to the correct operating pressure. Perform this test if the steering is erratic or unresponsive.Required Parts
Illustration 1 g02571852
Table 3
Required Tools
Tool Item Qty Part No Description
A 198-4240 Digital Pressure Indicator Gp
A1 1 198-4234 Digital Indicator
A2 1 198-4238 Pressure Sensor Gp
(0 to 35000 kPa (0 to 5000 psi))
A3 1 198-4236 Adapter Cable As
Connect Tool (A2) to Tool (A3) .
Connect Tool (A3) to Tool (A1).
Table 4
Optional Tools (1)
Tool Item Qty Part No Description
B 1 8T-0859 Pressure Gauges
C 1 030-7262 Hose As
( 1 ) The optional tools can be used to replace the digital pressure gauges in the required tool list.
Connect Tool (B) to Tool (C) .Test Preparation
Drive the machine to a smooth, horizontal surface.
Illustration 2 g03749808
Move propel lever (1) to the NEUTRAL position.
Move parking brake switch (4) to the ON position.
If the machine is equipped with a leveling blade, use blade control lever (3) to lower the blade to the ground.
Move throttle control switch (5) to the LOW-IDLE position.Note: The engine rpm will appear on machine display (2) .
Illustration 3 g03765758
Install steering frame lock (6) .
Illustration 4 g03765777
Allow the engine to run for 5 minutes. Move engine start switch (7) to the OFF position.
Illustration 5 g03765796
Connect Tool (A2) to pressure tap (8) .Test Procedure
Move engine start switch (7) to the START position. Release switch when engine starts.
Operate the engine at low idle for a few minutes. Move throttle control switch (5) to the HIGH-IDLE position. Engine speed should be 2200 50 rpm.Note: The engine rpm will appear on machine display (2) .
Operate the machine until the oil temperature reaches 38 °C (100 °F) minimum.Note: The oil temperature will appear on machine display (2) .
If equipped, move blade control lever (3) into the RAISE position, and raise the blade off the ground.
Turn the steering wheel, and record pressure on Tool (A). The pressure should be 21000 1000 kPa (3046 145 psi).
Release the steering wheel.
If equipped, place blade control lever (3) in the LOWER position, and lower the blade to the ground.
Move throttle control switch (5) into the LOW-IDLE position.Note: The engine rpm will appear on machine display (2) .
Allow engine to run for 5 minutes. Move engine start switch (7) to the OFF position.
Disengage steering frame lock (6) .
If the pressure recorded in Step 5 is outside the specified range, replace the steering control unit.
This procedure provides a method to determine if the steering relief valve is set to the correct operating pressure. Perform this test if the steering is erratic or unresponsive.Required Parts
Illustration 1 g02571852
Table 3
Required Tools
Tool Item Qty Part No Description
A 198-4240 Digital Pressure Indicator Gp
A1 1 198-4234 Digital Indicator
A2 1 198-4238 Pressure Sensor Gp
(0 to 35000 kPa (0 to 5000 psi))
A3 1 198-4236 Adapter Cable As
Connect Tool (A2) to Tool (A3) .
Connect Tool (A3) to Tool (A1).
Table 4
Optional Tools (1)
Tool Item Qty Part No Description
B 1 8T-0859 Pressure Gauges
C 1 030-7262 Hose As
( 1 ) The optional tools can be used to replace the digital pressure gauges in the required tool list.
Connect Tool (B) to Tool (C) .Test Preparation
Drive the machine to a smooth, horizontal surface.
Illustration 2 g03749808
Move propel lever (1) to the NEUTRAL position.
Move parking brake switch (4) to the ON position.
If the machine is equipped with a leveling blade, use blade control lever (3) to lower the blade to the ground.
Move throttle control switch (5) to the LOW-IDLE position.Note: The engine rpm will appear on machine display (2) .
Illustration 3 g03765758
Install steering frame lock (6) .
Illustration 4 g03765777
Allow the engine to run for 5 minutes. Move engine start switch (7) to the OFF position.
Illustration 5 g03765796
Connect Tool (A2) to pressure tap (8) .Test Procedure
Move engine start switch (7) to the START position. Release switch when engine starts.
Operate the engine at low idle for a few minutes. Move throttle control switch (5) to the HIGH-IDLE position. Engine speed should be 2200 50 rpm.Note: The engine rpm will appear on machine display (2) .
Operate the machine until the oil temperature reaches 38 °C (100 °F) minimum.Note: The oil temperature will appear on machine display (2) .
If equipped, move blade control lever (3) into the RAISE position, and raise the blade off the ground.
Turn the steering wheel, and record pressure on Tool (A). The pressure should be 21000 1000 kPa (3046 145 psi).
Release the steering wheel.
If equipped, place blade control lever (3) in the LOWER position, and lower the blade to the ground.
Move throttle control switch (5) into the LOW-IDLE position.Note: The engine rpm will appear on machine display (2) .
Allow engine to run for 5 minutes. Move engine start switch (7) to the OFF position.
Disengage steering frame lock (6) .
If the pressure recorded in Step 5 is outside the specified range, replace the steering control unit.
