AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1399740 - Caterpillar



1399740 ENGINE AR-COMPLETE Caterpillar parts C-10 ENGINE
Rating:
34
Alternative (cross code) number:
CA1399740
139-9740
1399740
Caterpillar 1399740 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1399740 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 1399740:

TRUCK ENGINE  C-10   Caterpillar
  For full view, you need register

Information:


Illustration 2 g03683142
Front main frame
Install Tooling (A) to the main screed frame.
Illustration 3 g03683143
Remove the two bolts, the two washers, and plate (1) from the left side of the main frame. Repeat step on the right side of the main frame.
Illustration 4 g03683145
Remove the lockwire from harness assemblies (2).
Disconnect harness assemblies (2).
Illustration 5 g03683146
Remove the four bolts and plate (3).
Illustration 6 g03683157
Remove the two bolts, the two washers, and plate (4).
Illustration 7 g03683164
Disconnect temperature sensor harness assembly (5).
Illustration 8 g03683165
Remove 24 nuts (6) and the 24 washers.
Loosen the 10 nuts and 12 bolts (7).
Illustration 9 g03683167
Start the machine. Slowly lift off the screed from screed plate (8). Verify that the harness assemblies do not get hooked to the extender screed frame. Place the screed on the travel locks.
Drive the tractor forward.
Illustration 10 g03683170
Remove clamp plate (13) and heater element (14) from screed plate (89).
Remove nut (9), the washers, and the clamp.
Remove the eight nuts, the eight washers, eight hold downs (10), and heater element (12) from screed plate (8).
Remove the eight studs used for hold downs (14).
Remove two temperature sensors (15) from screed plate (8).
Remove 24 studs (11). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Threaded Rod 1/2 - 13 THD x 5.25 inch 1
- Threaded Rod 1/2 - 13 THD x 3.25 inch 1
6V-8188 Nut 8
8T-4223 Hard Washer 8
B - Loctite 272 1
C 257-8023 Thermal Grease 1
D 459-0233 Strap Wrench 1
E 5P-6029 Lockwire 1
F 314-8478 Diagonal Cutter 1
Install screed plate (8) in the reverse order of removal.
Apply Tooling (B) to the shorter threaded end of 24 studs (11). Install 24 studs (11) to screed plate (8). Torque 24 studs (11) to 100 20 N m (74 15 lb ft).
Grind 24 studs (11) flush to the bottom of screed plate (8).
Apply Tooling (B) to the eight studs used for hold downs (10). Install the eight studs used for hold downs (10) to screed plate (8). Torque the eight studs used for hold downs (10) to 100 20 N m (74 15 lb ft).
Grind the eight studs used for hold downs (10) flush to the bottom of screed plate (8).
Apply Tooling (C) to temperature sensor (15). Install temperature sensor (15) to screed plate (8). Tighten temperature sensor (15) to a torque of 30 5 N m (22 4 lb ft).
Use Tool (D) and a torque wrench to tighten harness assemblies (2). Tighten harness assemblies (2) to a torque of 10.5 0.3 N m (93 3 lb in).
Use Tool (F) to install Tool (E) in order to secure harness assemblies (2). End By:
Install the nose bar (main screed). Refer to Disassembly and Assembly, "Nose Bar (Main Screed) - Remove and Install".

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.