AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1399785 - Caterpillar



1399785 ENGINE AR-COMPLETE Caterpillar parts C-10 ENGINE
Rating:
46
Alternative (cross code) number:
CA1399785
139-9785
1399785
Caterpillar 1399785 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1399785 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 1399785:

TRUCK ENGINE  C-10   Caterpillar
  For full view, you need register

Information:

Removal Procedure
Start By:
Remove the nose bar (extender). Refer to Disassembly and Assembly, "Nose Bar (Extender Screed) - Remove and Install".
Illustration 1 g03682685
Remove the lockwire from harness assemblies (1). Disconnect harness assemblies (1) from the electric screed heat box. Remove all the cable straps securing harness assemblies (1).
Illustration 2 g03682686
Disconnect harness assembly (2).
Remove the two bolts, the two washers, and plate assembly (3).
Illustration 3 g03682688
Lower the extender onto suitable cribbing.
Illustration 4 g03682689
Illustration 5 g03682699
Remove six nuts (4) and the six washers from the trailing-edge studs.
Remove bolt (5), the washer, and the clips in order to move harness assembly (6) out of the way.
Illustration 6 g03682705
Remove the two bolts and the two washers. Move electric screed heat box (7) out of the way.
Illustration 7 g03682692
Remove six nuts (8) and the six washers from the leading-edge studs.
Illustration 8 g03682775
Start the machine. Slowly lift off the screed from screed plate (9). Verify that the harness assemblies do not get hooked to the extender screed frame. Place the screed on the travel locks.
Drive the tractor forward.
Illustration 9 g03682776
Remove clamp plate (13) and heater element (11) from screed plate (9).
Remove the five nuts, the five washers, five hold downs (14), and heater element (15) from screed plate (9).
Remove the five studs used for hold downs (14).
Remove temperature sensor (12) from screed plate (9).
Remove 12 studs (10). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 272 1
B 257-8023 Thermal Grease 1
C 459-0233 Strap Wrench 1
D 5P-6029 Lockwire 1
E 314-8478 Diagonal Cutter 1
Install screed plate (9) in the reverse order of removal.
Apply Tooling (A ) to the shorter threaded end of 12 studs (10). Install12 studs (10) to screed plate (9). Torque twelve studs (10) to 100 20 N m (74 15 lb ft).
Grind 12 studs (10) flush to the bottom of screed plate (9).
Apply Tooling (A ) to the five studs used for hold downs (14). Install the five studs used for hold downs (14) to screed plate (9). Torque the five studs used for hold downs (14) to 100 20 N m (74 15 lb ft).
Grind the five studs used for hold downs (14) flush to the bottom of screed plate (9).
Apply Tooling (B) to temperature sensor (12). Install temperature sensor (12) to screed plate (9). Tighten temperature sensor (12) to a torque of 30 5 N m (22 4 lb ft).
Face the chamfer of screed plate (9) toward interior of the machine. Align the outside edge of screed plate (9) with the outside surface of the frame.
Align the front edge of screed plate (9) with the front face of the frame.
Use Tool (C) and a torque wrench to tighten harness assemblies (1). Tighten harness assemblies (1) to a torque of 10.5 0.3 N m (93 3 lb in).
Use Tool (E) to install Tool (D) in order to secure harness assemblies (1). End By:
Install the nose bar (extender). Refer to Disassembly and Assembly, "Nose Bar (Extender Screed) - Remove and Install".

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.