AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1399910 - Caterpillar



1399910 ENGINE AR-COMPLETE Caterpillar parts 3406E ENGINE
Rating:
23
Alternative (cross code) number:
CA1399910
139-9910
1399910
Caterpillar 1399910 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1399910 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 1399910:

TRUCK ENGINE  3406E   Caterpillar
  For full view, you need register

Information:

(1) Bore in connecting rod for piston pin bearing ... 55.436 0.013 mm (2.1825 .0005 in.) Tight fit between connecting rod eye and piston pin bearing ... 0.05 to 0.10 mm (.002 to .004 in.) Connecting rod must be heated for installation of piston pin bearing. Do not use a torch.Heat connecting rod to temperature of ... 177 to 260°C (350 to 500°F)
POSITIONING PIN BEARING Piston pin bearing junction and locating hole are 180° apart (directly across from each other). Bearing junction and locating hole must be assembled within either area "A" (90 10° from centerline through the connecting rod bores) as shown.Make reference to Special Instruction Form No. SMHS7295 for use of pin bearing removal and installation tools and procedures.(2) Bore in connecting rod for bearing with nuts tight to specifications (6) ... 103.500 0.013 mm (4.078 .0005 in.)(3) Distance between center of bearings ... 261.62 0.05 mm (10.300 .002 in.)(4) Bore in bearing for piston pin (new) ... 50.830 0.008 mm (2.0012 .0003 in.) Diameter of piston pin (new) ... 50.795 0.005 mm (1.9998 .0002 in.)Maximum permissible clearance between bearing and piston pin (worn) ... 0.08 mm (.003 in.)(5) Bore in bearing for crankshaft ... 97.119 to 97.175 mm (3.8236 to 3.8258 in.) Clearance between bearing and crankshaft (new) ... 0.071 to 0.168 mm (.0028 to .0066 in.)Maximum permissible clearance between bearing and crankshaft (worn) ... 0.25 mm (.010 in.) Bearings are available in 0.64 mm (.025 in.) and 1.27 mm (.050 in.) smaller than original size.
MARKS FOR TIGHTENING CONNECTING ROD BOLTS(6) Tightening procedure for connecting rod bolts: a. Put 2P2506 Thread Lubricant on bolt threads and contact surfaces of nut and cap.b. Tighten both nuts to ... 80 8 N m (60 6 lb.ft.)c. Put a mark on each nut and end of bolt as shown.d. Tighten each nut from mark ... 120 5°Make reference to Special Instruction Form Nos. GMG02394 & SMHS7366 for information to check and recondition connecting rods. Also see GUIDELINE FOR REUSABLE PARTS; SALVAGE OF NON-SERRATED CONNECTING RODS, Form No. SEBF8064.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.