AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1399984 - Caterpillar



1399984 ENGINE AR-COMPLETE Caterpillar parts 3406E ENGINE
Rating:
21
Alternative (cross code) number:
CA1399984
139-9984
1399984
Caterpillar 1399984 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1399984 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 1399984:

TRUCK ENGINE  3406E   Caterpillar
  For full view, you need register

Information:

Put a small amount of clean engine oil or glycerine on the lip of seal (4) and in the bores for the O-ring seals at assembly.(1) Distance bearing is installed below pipe surface ... 0.25 0.25 mm (.010 .010 in.)(2) Diameter of shaft ... 15.80 0.03 mm (.622 .001 in.) Bore in bearings ... 15.88 mm (.625 in.)Bore in pipe for bearings ... 18.263 0.013 mm (.7190 .0005 in.)(3) Valve assembly shown in the "run" (open) position. When the valve is closed a 0.08 mm (.003 in.) feeler gauge must not fit between the valve and the bore in the pipe at any point.(4) Seal. Install the seal with the tip of the seal toward the outside as shown.(5) Diameter of shaft ... 9.60 0.03 mm (.378 .001 in.) Bore in the bearing ... 9.80 0.03 mm (.386 .001 in.) Adjust shaft as needed to change spring tension until hold-in current consumption (draw) is less than 2A at shutdown.(6) 3N9106 Torsion Spring (used with some 3406 Engines): Free length ... 63.5 mm (2.50 in.)Outside diameter ... 30.7 mm (1.21 in.)5N2761 Torsion Spring:Free length ... 49.8 0.5 mm (1.96 .02 in.)Outside diameter ... 30.7 0.5 mm (1.21 .02 in.)(7) 3N7848 Spring: Length under test force ... 22.86 0.5 mm (.90 .02 in.)Test force ... 4 N (1 lb.)Free length after test ... 35.6 0.5 mm (1.40 .02 in.)Outside diameter ... 18.8 0.5 mm (.74 .02 in.)(8) Bracket assembly. Bracket assembly must be adjusted so valve assembly (3) is parallel to pipe bore within 2°.(9) 4N3889 Solenoid: Voltage rating ... 12VCurrent consumption (draw): Pull-in windings ... 21A at 12VHold-in windings ... Below 1A at 14.3V4N3890 Solenoid:Voltage rating ... 24 or 32VCurrent consumption (draw): Pull-in windings ... 10A at 24VHold-in windings ... Below 1A at 28V4N3889 and 4N3890 Solenoids:Plunger travel ... 11.7 0.3 mm (.46 .01 in.)Distance from plunger face to flange face: with solenoid energized* ... 9.6 0.5 mm (.38 .02 in.)with plunger extended ... 21.28 0.13 mm (.838 .005 in.)*The hold-in current consumption (draw) on engine must take less than 2A at shutdown.(10) Diode assembly. Diode assembly required to suppress the back EMF voltage spike generated when the solenoid is turned off.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.