AVSPARE.COM
parts catalog

ENGINE AR-COMPLETE 1399995 - Caterpillar



1399995 ENGINE AR-COMPLETE Caterpillar parts 3406C ENGINE
Rating:
36
Alternative (cross code) number:
CA1399995
139-9995
1399995
Caterpillar 1399995 ENGINE AR-COMPLETE

Buy ENGINE AR-COMPLETE 1399995 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 1399995:

TRUCK ENGINE  3406C   Caterpillar
  For full view, you need register

Information:


Illustration 1 g02039528
Schematic of the "Boom Low Pressure Relief Enable" SolenoidThis diagnostic code is associated with the "Boom Low Pressure Relief Enable" Solenoid. The FMI 06 diagnostic code means that the Machine ECM has determined that the current of the solenoid is above normal.The possible causes of this diagnostic code are listed below:
The energizer circuit of the solenoid for the modulating valve is shorted to ground.
The solenoid has failed.
The Machine ECM has failed. A failure of the ECM is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 3038 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active, the Machine ECM will turn off the current to the failed solenoid.Test Step 1. CHECK THE SOLENOID
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:The CID 3038 FMI 06 diagnostic code changes to a CID 3038 FMI 05 diagnostic code when the solenoid is disconnected.Results:
YES - The CID 3038 FMI 06 diagnostic code changes to a CID 3038 FMI 05 diagnostic code when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.STOP
NO - The CID 3038 FMI 06 diagnostic code remains active. Proceed to Test Step 2.Test Step 2. CHECK THE SOLENOID ENERGIZER CIRCUIT FOR A SHORT TO GROUND
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connectors from the Switch Panel.
At the machine harness connector, measure the resistance from the signal contact C2-14 (wire C475-PU) to all contacts that are used in the machine harness connectors for the Switch Panel.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between C2-14 (wire C475-PU) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS
Inspect the harness connectors. Clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 3038 FMI 06 diagnostic code.Expected Result:The CID 3038 FMI 06 diagnostic code is active.Results:
YES - The CID 3038 FMI 06 diagnostic code is active. The diagnostic code has not been corrected. The Machine ECM may have failed.Repair: A failure of the Switch Panel is

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts engine Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.