1731333 ENGINE AR-CORE Caterpillar parts
3126B, 3126E
Rating:
Alternative (cross code) number:
CA1731333
173-1333
1731333
CA1731333
173-1333
1731333
TRUCK ENGINE,
Related part:
1731333
SHORT BLOCK
0R4890
R
Information:
Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01470403
Typical example
Remove the bolts from Position (X) from flywheel housing (1).
Install Tooling (A) into Position (X) on flywheel housing (1).
Install a suitable lifting device to the flywheel housing in order to support the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb).
Illustration 2 g01763013
Typical example
Illustration 3 g03713998
Remove bolts (2) and remaining bolts (3) from flywheel housing (1).
If equipped, remove bolts (4).
Use the lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 4 g03714001
Typical example
If the engine has an aluminum oil pan, remove dust seal (6).
If necessary, remove dowels (5) from the cylinder block. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Bolt
M10 by 100 mm 2
B 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all tapped holes and bolt threads are clean, dry, and free from lubricant.
Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing.
Illustration 5 g03714002
Typical example
Inspect crankshaft rear seal (7) for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Clean the rear face of the cylinder block. If necessary, install dowels (5) to the cylinder block.
Install Tooling (A) to the cylinder block.
If an aluminum oil pan is installed, install dust seal (6).
Illustration 6 g01763034
Typical example
Illustration 7 g03713998
Install a suitable lifting device to the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb).
Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block.
Install bolts (2) and bolts (3) finger tight.
Remove Tooling (A). Install remaining bolts (3).
If equipped, install bolts (4) finger tight.
Tighten bolts (3) to a torque of 63 N m (46 lb ft).
Tighten bolts (2) to a torque of 75 N m (55 lb ft).
If equipped, tighten bolts (4) to a torque of 44 N m (32.45 lb ft).
Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect" for the correct procedure. End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct procedure.
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01470403
Typical example
Remove the bolts from Position (X) from flywheel housing (1).
Install Tooling (A) into Position (X) on flywheel housing (1).
Install a suitable lifting device to the flywheel housing in order to support the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb).
Illustration 2 g01763013
Typical example
Illustration 3 g03713998
Remove bolts (2) and remaining bolts (3) from flywheel housing (1).
If equipped, remove bolts (4).
Use the lifting device in order to remove flywheel housing (1) from the cylinder block.
Illustration 4 g03714001
Typical example
If the engine has an aluminum oil pan, remove dust seal (6).
If necessary, remove dowels (5) from the cylinder block. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Bolt
M10 by 100 mm 2
B 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all tapped holes and bolt threads are clean, dry, and free from lubricant.
Ensure that the flywheel housing is clean and free from damage. If necessary, replace the flywheel housing.
Illustration 5 g03714002
Typical example
Inspect crankshaft rear seal (7) for leaks. If there are any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Clean the rear face of the cylinder block. If necessary, install dowels (5) to the cylinder block.
Install Tooling (A) to the cylinder block.
If an aluminum oil pan is installed, install dust seal (6).
Illustration 6 g01763034
Typical example
Illustration 7 g03713998
Install a suitable lifting device to the flywheel housing. The flywheel housing weighs approximately 30 kg (66 lb).
Use the lifting device to align flywheel housing (1) with Tooling (A). Install the flywheel housing to the cylinder block.
Install bolts (2) and bolts (3) finger tight.
Remove Tooling (A). Install remaining bolts (3).
If equipped, install bolts (4) finger tight.
Tighten bolts (3) to a torque of 63 N m (46 lb ft).
Tighten bolts (2) to a torque of 75 N m (55 lb ft).
If equipped, tighten bolts (4) to a torque of 44 N m (32.45 lb ft).
Use Tooling (B) to check the alignment of the flywheel housing with the crankshaft. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect" for the correct procedure. End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct procedure.
Caterpillar SIS machinery equipment:
Cat SIS web machinery list:
Parts engine Caterpillar catalog:
1538920
ENGINE HARNESS ASSEMBLY
120H, 135H, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
120H, 135H, 3126, 3126B, 3126E, 322C, 322C FM, 325C, 325C FM, 561N, 570B, 580B, 938G II, 950G II, 953C, 962G II, 963C, C7, D5N, D6N, IT38G II, IT62G II, M325C MH, SPP101
1971065
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1971083
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1971164
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1971184
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1971192
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1971205
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1971213
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1971283
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1998653
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1998835
ENGINE AR-COMPLETE
3126B, 3126E
3126B, 3126E
1731332
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1731331
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1731330
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1731329
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1731328
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1731327
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1923342
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1796570
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1731337
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1731336
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1731335
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E
1731334
ENGINE AR-CORE
3126B, 3126E
3126B, 3126E